turbo dismantle
#1
turbo dismantle
i noticed a few months back someone posted up a thread showing pics of them taking a holset turbo( or a turbo off a cummins) apart. i was wondering if there ever was a thread like this or if someone could post pics of how to take the from part of the turbo off so i could get it powder coated
#2
#3
Here's a 16cm Holset Exhaust Housing
Here's the Exhaust Gasket
Here's the Oil Return Line Gasket
Here's the donor charger
This set up is a Holset HX35W with a Modified 21 Cm Exhaust Housing to fit the newer model Cummins that don't have the clamp style Connection to the down pipe
Here's the Exhaust Gasket
Here's the Oil Return Line Gasket
Here's the donor charger
This set up is a Holset HX35W with a Modified 21 Cm Exhaust Housing to fit the newer model Cummins that don't have the clamp style Connection to the down pipe
Last edited by DB Admin; 11-22-2008 at 10:39 PM.
#4
Separating the charger
Remove the 4 bolts
the 2 rings will then come off this is what they look like
Spray a bunch of the best penetrating oil you can find around the connection of the Exhaust Housing and the Compressor Housing and wait for it to penetrate.
You do not want to separate the two parts violently there is a fragile shaft that runs the length of the turbo and connects the compressor wheel and the exhaust turbine
Bend it and you're done for !
Here it is coming apart
Apart picks below:
Here's the exhaust turbine
Now that its apart take the 16 Cm housing and slide it on over the exhaust turbine
Set one of the rings in place
Remove the 4 bolts
the 2 rings will then come off this is what they look like
Spray a bunch of the best penetrating oil you can find around the connection of the Exhaust Housing and the Compressor Housing and wait for it to penetrate.
You do not want to separate the two parts violently there is a fragile shaft that runs the length of the turbo and connects the compressor wheel and the exhaust turbine
Bend it and you're done for !
Here it is coming apart
Apart picks below:
Here's the exhaust turbine
Now that its apart take the 16 Cm housing and slide it on over the exhaust turbine
Set one of the rings in place
#5
You will only use the center hole of the 3 grouped together on the rings
Put each ring on and put the middle bolt in to hold the rings while your putting the other 2 bolts in
The ends of the rings have arcs cut in them and when both rings are on that's where the bolt goes like so
Reference picture only
Leave the bolts hand tight
Here's the new set up HX35W With A 16 Cm Exhaust Housing
Put the charger on the truck using the Exhaust Gasket (BUBBLE OUT) and connect the charger to the Exhaust Manifold.
Spin the charger around to where the Intercooler line is perfectly lined up then tighten down all 4 bolts connecting the Exhaust Housing and the Compressor Housing
Finish putting the charger on and you're done
Put each ring on and put the middle bolt in to hold the rings while your putting the other 2 bolts in
The ends of the rings have arcs cut in them and when both rings are on that's where the bolt goes like so
Reference picture only
Leave the bolts hand tight
Here's the new set up HX35W With A 16 Cm Exhaust Housing
Put the charger on the truck using the Exhaust Gasket (BUBBLE OUT) and connect the charger to the Exhaust Manifold.
Spin the charger around to where the Intercooler line is perfectly lined up then tighten down all 4 bolts connecting the Exhaust Housing and the Compressor Housing
Finish putting the charger on and you're done
#6
#7
#9
Here is my write up on the H1C/H1E hybrid I built....
https://www.dieselbombers.com/5-9l-r...-call-h1d.html
https://www.dieselbombers.com/5-9l-r...-call-h1d.html
Thread
Thread Starter
Forum
Replies
Last Post
avatardvr
Ford Powerstroke 03-07 6.0L
18
08-08-2019 12:38 AM
tumble72
Ford 83-94 6.9 and 7.3L General
8
11-27-2014 10:31 PM