24 Valve 2nd Gen Dodge Cummins 98.5-02 Discussion of 24 Valve 5.9 Liter Dodge Cummins Diesels with VP44 Injection Pumps
Sponsored by Trailer Plus

24 valve cutting out, need help

Thread Tools
 
Search this Thread
 
  #1  
Old 05-16-2010, 05:16 PM
guroo987's Avatar
Diesel Fan
Thread Starter
Join Date: Mar 2007
Location: fallon, nv
Posts: 61
Likes: 0
Received 13 Likes on 4 Posts
Default 24 valve cutting out, need help

been a while but here goes.
lost injection pump at 129,000, bought special x from blue chip, installed with no problems, fired it up and idled perfect, let it warm up and took for a test drive and it was cutting out at all rpms except at idle. now when i say cutting out it would just die for a milisecond and come right back, perty violently. called chip and he said it is a apps problem cause it doesnt do it at idle, only when the apps goes into closed loop. he suggested i check the connections, i did and they were all good. problem went away i thought until i took it on a 400 mile trip and it did it about 20 times cruising at 75 mph. next day no problem again. about 2 weeks go by and it is back at all rpms again but intermitent. never had a prob until changed IP. recalibrated apps and it was way out of range, within .01 volt now with no change. today whwn it acted up it was doing it at idle in gear to but not in neutral. fuel press is always between 16-13. does it with chip on or off. IP does have one of chips stelth covers on it. ANY HELP APPRECIATED!!! THANKS IN ADVANCE!!! AND NO CODES!!!
 
  #2  
Old 05-16-2010, 05:23 PM
Join Date: Mar 2007
Location: Western NC
Posts: 14,546
Received 843 Likes on 695 Posts
Default

Could still be a APPS issue.
 
  #3  
Old 05-16-2010, 06:08 PM
guroo987's Avatar
Diesel Fan
Thread Starter
Join Date: Mar 2007
Location: fallon, nv
Posts: 61
Likes: 0
Received 13 Likes on 4 Posts
Default

it seems like an apps issue but it is hard for me to buy a new one when there was no problem there before the new injection pump
 
  #4  
Old 05-17-2010, 07:32 PM
guroo987's Avatar
Diesel Fan
Thread Starter
Join Date: Mar 2007
Location: fallon, nv
Posts: 61
Likes: 0
Received 13 Likes on 4 Posts
Default

anybody???
 
  #5  
Old 05-19-2010, 10:50 PM
jkidd's Avatar
Diesel Bombers Sponsor
Join Date: Jan 2008
Location: Kaysville UT
Posts: 1,100
Received 77 Likes on 71 Posts
Default

Any codes? If you need a new apps or tps don't buy it at the dealer. you can get them for less than $200.
 
  #6  
Old 05-20-2010, 07:07 AM
RAW's Avatar
RAW
RAW is offline
Administrator

iTrader: (1)
Join Date: Aug 2009
Location: Alberta
Posts: 6,218
Received 684 Likes on 549 Posts
Default

How about your Cam sensor or wiring to it? Tricky little devil hides behind the VP, so it is hard to test. I don't suppose you changed the sensor when the P was removed?
 
  #7  
Old 05-20-2010, 09:26 PM
guroo987's Avatar
Diesel Fan
Thread Starter
Join Date: Mar 2007
Location: fallon, nv
Posts: 61
Likes: 0
Received 13 Likes on 4 Posts
Default

no i did not change the sensor. and there are NO CODES
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Bill in Ballard
Ford 83-94 6.9 and 7.3L General
3
03-13-2016 07:42 PM
jeremiah1
5.9 Liter CR Dodge Cummins 03-07
0
07-21-2015 06:35 PM
LTreis702
Chevy/GMC 6.2L and 6.5L
4
02-14-2015 12:52 PM
bonestock
24 Valve 2nd Gen Dodge Cummins 98.5-02
0
02-01-2015 08:41 PM
woodsman27
12 Valve 2nd Gen Dodge Cummins 94-98
5
10-26-2014 02:13 AM



Quick Reply: 24 valve cutting out, need help



All times are GMT -5. The time now is 12:32 PM.