Looking For Some Better Spool Up, M&H M2 Fuel Pin?
Diesel Bomber
Joined: Jul 2009
Posts: 1,861
Likes: 86
From: Kingwood, WV
as i said before too much fuel can be a problem and as rswords had explained with better termonology it can actually hinder the flame that is produced by the combustion. which means it leads to more inefficiency than it does power; until of course you see the higher boost levels... he wants to keep the top end fuel that the denny T provides but he'd like to reduce low end fuel as it is hurting his spool up, if you get the right ammount of fuel for air that is present at low end then you'll produce more gasses thru complete combustion than you would from excessive fuel and an incomplete burn. more gasses will porduce higher drive pressures, greater force to drive the turbo sooner and so on. i doubt he has to worry about boost anyways for what he's running 
a single silver 62 is one hell of a charger
a single silver 62 is one hell of a charger
Diesel Enthusiast
Joined: Jan 2009
Posts: 267
Likes: 17
From: New England
In my opinion with big sticks ( 6x16's or 6x18's ) the m2 is the way to go. 
Less fuel on bottom and massive fuel on top.
Diesel Enthusiast
Joined: Jan 2009
Posts: 267
Likes: 17
From: New England
It does take some tuning to get it right. When I installed mine I had the starwheel way up. It made it a dog on the low side then when the pin droped down with boost it made like 7 psi more then a stock pin turned to deepest. I put the starwheel down some to get a little more fuel early. Basically it allows you to make more of a difference with starwheel and smoke screw settings. With a stock cone the starwheel and smoke screw are mild adjustments. With the extra depth as well as a shallower end it just adds to the tunibility.
Thread Starter
|
BOMBARDIER
Joined: Mar 2007
Posts: 11,159
Likes: 918
From: Gloucester, VA
boost fooler sounds like a good alternative or maybe a really small orfice to restrict air flow and delay boost to the diaphragm... the boost fooler is going to do the same thing as the valet... maybe not as instantaneous. but what about the bleed off when the pin is supposed to return to "low fuel" i know the boost elbow or fooler has a small weep hole but if you rock out of the throttle; lose boost and rock back in the pin may still be held in a deeper fuel setting causing more lag and excessive black smoke... but with any kinda of performance; gotta lose some to gain some
as i said before too much fuel can be a problem and as rswords had explained with better termonology it can actually hinder the flame that is produced by the combustion. which means it leads to more inefficiency than it does power; until of course you see the higher boost levels... he wants to keep the top end fuel that the denny T provides but he'd like to reduce low end fuel as it is hurting his spool up, if you get the right ammount of fuel for air that is present at low end then you'll produce more gasses thru complete combustion than you would from excessive fuel and an incomplete burn. more gasses will porduce higher drive pressures, greater force to drive the turbo sooner and so on. i doubt he has to worry about boost anyways for what he's running a single silver 62 is one hell of a charger
a single silver 62 is one hell of a chargerIt does take some tuning to get it right. When I installed mine I had the starwheel way up. It made it a dog on the low side then when the pin droped down with boost it made like 7 psi more then a stock pin turned to deepest. I put the starwheel down some to get a little more fuel early. Basically it allows you to make more of a difference with starwheel and smoke screw settings. With a stock cone the starwheel and smoke screw are mild adjustments. With the extra depth as well as a shallower end it just adds to the tunibility.
