Ford Powerstroke 94-98 7.3L Discussion of 94-98 7.3 Liter Ford Powerstroke Turbo Diesels

7.3L problems

Thread Tools
 
Search this Thread
 
  #1  
Old 12-03-2013, 08:01 PM
tstacoma's Avatar
Newbie
Thread Starter
Join Date: Dec 2013
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default 7.3L problems

I got a 1995 f250 four wheel drive got it for cheap ($3,000) Arkansas truck no rust, my buddy got it when it had no motor so he had to put a motor in the truck, he got a 1996 7.3L he sold it to me without it running so I finished up the motor job got it done and got it started well it smoked so much white it burned your eyes so we drove it out side (at 20 degs) it wouldn't idle we held down the throttle at 1,000 rpm until it was warmed up then it idled took it down the road it had no power and smoked so bad you couldn't see the road, well going up and over a hill it shut off and won't start got her towed home and found starter was stuck to the flywheel replaced starter and still did nothing found out the power cable starter to battery was rubbed threw and shorted out well my question is why did it shut off I was thinking IPR?? Haven't had time to get it started again but I need help what could white smoke be bad injector o rings? From the motor sitting?
 
  #2  
Old 12-03-2013, 08:08 PM
autostroker's Avatar
Diesel Enthusiast
Join Date: Jan 2013
Location: iowa
Posts: 188
Likes: 0
Received 9 Likes on 8 Posts
Default

Bad injector orings could cause the smoke, lack of power and shut down. If its loosing enough high pressure oil it eont fire the injectors

Sent from my SCH-R970 using Tapatalk
 
  #3  
Old 12-03-2013, 08:11 PM
tstacoma's Avatar
Newbie
Thread Starter
Join Date: Dec 2013
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Is there a good way to test for injector o rings
 
  #4  
Old 12-03-2013, 08:23 PM
autostroker's Avatar
Diesel Enthusiast
Join Date: Jan 2013
Location: iowa
Posts: 188
Likes: 0
Received 9 Likes on 8 Posts
Default

Not sure if buzz test would work or not... only other way i know is to have it running and see if oil dril spouts are pouring oil out like they should.

Sent from my SCH-R970 using Tapatalk
 
  #5  
Old 12-03-2013, 08:24 PM
joebob3093's Avatar
Moderator
Join Date: Jul 2008
Location: Powell Butte, OR
Posts: 2,558
Received 138 Likes on 122 Posts
Default

not really, you have to pull them. but once you pull them you have to replace them. its not wise to reuse them
 
  #6  
Old 12-03-2013, 08:29 PM
autostroker's Avatar
Diesel Enthusiast
Join Date: Jan 2013
Location: iowa
Posts: 188
Likes: 0
Received 9 Likes on 8 Posts
Default

Not too bad of a job anyway.

Sent from my SCH-R970 using Tapatalk
 
  #7  
Old 12-03-2013, 10:11 PM
joebob3093's Avatar
Moderator
Join Date: Jul 2008
Location: Powell Butte, OR
Posts: 2,558
Received 138 Likes on 122 Posts
Default

Takes me 4-6 hours depending on how everything is cooperating
 
  #8  
Old 12-05-2013, 02:41 PM
7.3OilPanRepair's Avatar
FormerVendor
Join Date: May 2010
Location: NC
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Default

Inexpensive and fairly easy repair. Do the glow plugs too while your under the valve cover. Replacing the orings on mine didnt stop it from smoking, but I did find a few that were brittle and cracked. You can get the orings for like 7bucks per injector. I think mine is still smoking because the injectors are worn and 15w oil is so thick when cold.
Everything is normal if the block heater has been plugged up for a few hours
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Bloom12valve
12 Valve 2nd Gen Dodge Cummins 94-98
1
10-09-2015 03:40 PM
Brody Olson
Chevy/GMC Duramax 06-07 LBZ
1
09-12-2015 11:01 PM
Dye Guardian
Ford Powerstroke 94-98 7.3L
0
08-01-2015 01:28 PM
Bstehle
Diesel In Distress - Support Ticket
2
02-03-2015 07:24 PM
Blue Briar
Diesel In Distress - Support Ticket
1
10-05-2014 08:23 AM



Quick Reply: 7.3L problems



All times are GMT -5. The time now is 04:54 PM.