cummins boost elbow
#21
ok guys i have a 1996 and the boost fitting is on the back of the lift pump with a steel line that runs to the waste gate.
i have a 5spd nv4500 tranny.
im gunna go look now of the model of the turbo and take pictures
---AutoMerged DoublePost---
Here are the two pics i just got. my turbo is a hx35w on a 1996 ram 2500 cummins 12 valve
this one shows there is no boost elbow on the turbo
http://i431.photobucket.com/albums/q...lein/turbo.jpg
this is the one that shows the boost fitting on the afc housing.
http://i431.photobucket.com/albums/q...boostelbow.jpg
hope this clears things up
i have a 5spd nv4500 tranny.
im gunna go look now of the model of the turbo and take pictures
---AutoMerged DoublePost---
Here are the two pics i just got. my turbo is a hx35w on a 1996 ram 2500 cummins 12 valve
this one shows there is no boost elbow on the turbo
http://i431.photobucket.com/albums/q...lein/turbo.jpg
this is the one that shows the boost fitting on the afc housing.
http://i431.photobucket.com/albums/q...boostelbow.jpg
hope this clears things up
Last edited by dan33klein; 11-24-2008 at 05:50 PM. Reason: Automerged Doublepost
#22
All right I did alil research and I learned something new! I am by no means a 12v expert, but the confusion is coming from the fact that there are two different ways the wastegate line is set up. On some there is a line from the AFC to the wastegate actuator, on others there is no line across the engine, just a short line from the turbo output to the actuator. Since you have the line going across your engine install the elbow on the tee at the rear of your injection pump where the line to the wastegate starts. Hope this helps!
#24
Ok guys i just installed my guages (boost, pyrometer) and i have a question
What should my truck make for boost?
idk if my guage is messed up
it doesnt make any boost at an idle
and just going down the road it isnt make much if not any.
it olny makes it when i mash the go pedal it soars
but just driving at say 40 mph it says zero.
whats up with that
i got the fitting in the afc housing like your supposed to and the hose isnt kinked.
thanks
What should my truck make for boost?
idk if my guage is messed up
it doesnt make any boost at an idle
and just going down the road it isnt make much if not any.
it olny makes it when i mash the go pedal it soars
but just driving at say 40 mph it says zero.
whats up with that
i got the fitting in the afc housing like your supposed to and the hose isnt kinked.
thanks
#25
No boost at idle is norm... Depending on where you set the boost fooler at max I dunno. Stock is like 23-26? And boost all depends on the load on the engine, at 40 what are your rpms at? Is yours a 60lb gauge, they're not to sensitive down low. But on my truck at 70 I'm making about 10 - 12lbs.
#26
couldnt tell you rpms at the moment.
it just seems like the needle sits at zero untill i mash it then itl soar to about 25.
im stalling my boost elbow tommrow so itl make more boost
i have a 5sp
and idk how just accelerating normal isnt making any boost
it just seems like the needle sits at zero untill i mash it then itl soar to about 25.
im stalling my boost elbow tommrow so itl make more boost
i have a 5sp
and idk how just accelerating normal isnt making any boost
Thread
Thread Starter
Forum
Replies
Last Post
somarillw
Dodge Truck and Cummins Turbo Diesel Forum
0
12-04-2014 12:37 AM
Diesel Bombers
General Diesel Related
0
10-31-2014 08:10 AM
Diesel Bombers
General Diesel Related
0
10-24-2014 04:40 AM
Omingnome
Diesel In Distress - Support Ticket
5
10-20-2014 12:25 PM