Can you smoke switch a 6.7???
#82
#83
usually if you leave it on for more then like 10 seconds you will get the lighting bolt light, how long are you leaving it on and do you think you maybe left it on too long and thats why it triggered it. Also it doesnt matter what tuning you are using, the only affect that will have is the amount of smoke it puts out.
#84
#85
What you need:
-T-tap connectors
-16 gage wire
-100ohm 10 Watt resistor
-On/Off switch
-Shrink Wrap
**Tuner is needed to produce "thick" smoke**
Step 1:
Locate Map sensor.
Step 2: Tap into Pink(with yellow stripe) wire and solid Brown sire with T-tap connectors.
Step 3:
Tie 100ohm 10 Watt resistor into either wire (it doesn't matter what one)
Step 4:
Shrink Wrap around resistor.
Step 5:
Run wires into cab.
Step 6:
Locate where to mount switch.
Step 7:
Start truck and make sure she smokes before fully connecting switch. (if you have a boost gage it should read that you are at full boost once switch is flipped.)
Step 8:
Mount switch.
---AutoMerged DoublePost---
there are some pictures back on page 2
-T-tap connectors
-16 gage wire
-100ohm 10 Watt resistor
-On/Off switch
-Shrink Wrap
**Tuner is needed to produce "thick" smoke**
Step 1:
Locate Map sensor.
Step 2: Tap into Pink(with yellow stripe) wire and solid Brown sire with T-tap connectors.
Step 3:
Tie 100ohm 10 Watt resistor into either wire (it doesn't matter what one)
Step 4:
Shrink Wrap around resistor.
Step 5:
Run wires into cab.
Step 6:
Locate where to mount switch.
Step 7:
Start truck and make sure she smokes before fully connecting switch. (if you have a boost gage it should read that you are at full boost once switch is flipped.)
Step 8:
Mount switch.
---AutoMerged DoublePost---
there are some pictures back on page 2
Last edited by coors_man_2005; 01-17-2011 at 09:20 PM. Reason: Automerged Doublepost
The following users liked this post:
Miller (01-18-2011)
#86
I cant believe this thread is still runnin strong, AWESOME! Just an update for new switch guys, ran mine for over a yr now, 15,000+ miles rollin coal on every power joke puffin choke dura crack possible and not one problem to report....other then replacing the rocker switch cause I wore it out!
Happy smokin
Mike
Happy smokin
Mike
The following users liked this post:
snakebite2004 (09-09-2011)
#87
I cant believe this thread is still runnin strong, AWESOME! Just an update for new switch guys, ran mine for over a yr now, 15,000+ miles rollin coal on every power joke puffin choke dura crack possible and not one problem to report....other then replacing the rocker switch cause I wore it out!
Happy smokin
Mike
Happy smokin
Mike
#88
#89
different strokes for different folks.. question.. when you trip the circuit what is the truck gonna do besides smoke more?? just want to know in case something im doing is wrong..
---AutoMerged DoublePost---
what is a fleece controller?? where can u get one? install??
---AutoMerged DoublePost---
hooked mine up and got a really cloud of smoke.. but the third time i hit the pedal no smoke.. and will harldy smoke while going down the road.. i have the three connector rocker switch.. and what is this lighting bolt??
---AutoMerged DoublePost---
what is a fleece controller?? where can u get one? install??
---AutoMerged DoublePost---
hooked mine up and got a really cloud of smoke.. but the third time i hit the pedal no smoke.. and will harldy smoke while going down the road.. i have the three connector rocker switch.. and what is this lighting bolt??
Last edited by ryan6.7; 03-15-2012 at 05:41 PM. Reason: Automerged Doublepost
#90
ive noticed with mine that if i flip the switch with the truck running and in park, rev it, i get zero smoke and a lightning bolt.... but cruise down a barren *** back road at about 25, hit the switch, and lightly step into the throttle, it will roll out some soot.
mods are Mini Maxx with all deletes and 4" turbo back straight pipes
mods are Mini Maxx with all deletes and 4" turbo back straight pipes