LIVE VP44 TAPPING NEED HELP!!!
#1
LIVE VP44 TAPPING NEED HELP!!!
Need your help guys; I’m installing the Edge with an attitude 31000 as you read this email.
I’ve incorrectly tapped two wires on the VP44, (truck was a mess), I’m showing two pictures for you to tell me which wire should I be tapping;
This is a VP44 stock replacement,
Also now that I’m in a roll, where would you install the fuel sensor at the VP44 inline or right at the filter outline casing,.,,…
Thanks for the helpk
I’ve incorrectly tapped two wires on the VP44, (truck was a mess), I’m showing two pictures for you to tell me which wire should I be tapping;
This is a VP44 stock replacement,
Also now that I’m in a roll, where would you install the fuel sensor at the VP44 inline or right at the filter outline casing,.,,…
Thanks for the helpk
#2
Need your help guys; I’m installing the Edge with an attitude 31000 as you read this email.
I’ve incorrectly tapped two wires on the VP44, (truck was a mess), I’m showing two pictures for you to tell me which wire should I be tapping;
This is a VP44 stock replacement,
Also now that I’m in a roll, where would you install the fuel sensor at the VP44 inline or right at the filter outline casing,.,,…
Thanks for the helpk
I’ve incorrectly tapped two wires on the VP44, (truck was a mess), I’m showing two pictures for you to tell me which wire should I be tapping;
This is a VP44 stock replacement,
Also now that I’m in a roll, where would you install the fuel sensor at the VP44 inline or right at the filter outline casing,.,,…
Thanks for the helpk
Anybody?> bump
#3
http://edgeproducts.com/installation_guides/31100_B.pdf
Page 12 and 13 show it very well. You did get into the wrong harness. The harness that leads to the center of the all the injector line outlets is the one you are after. In that two wire bundle, you want the one closer to the engine.
You do want the sensor at the inlet, yes. Hard to tell by the picture, but is there a tapped banjo bolt there?
Page 12 and 13 show it very well. You did get into the wrong harness. The harness that leads to the center of the all the injector line outlets is the one you are after. In that two wire bundle, you want the one closer to the engine.
You do want the sensor at the inlet, yes. Hard to tell by the picture, but is there a tapped banjo bolt there?
The following users liked this post:
somarillw (12-14-2014)
#4
http://edgeproducts.com/installation_guides/31100_B.pdf
Page 12 and 13 show it very well. You did get into the wrong harness. The harness that leads to the center of the all the injector line outlets is the one you are after. In that two wire bundle, you want the one closer to the engine.
You do want the sensor at the inlet, yes. Hard to tell by the picture, but is there a tapped banjo bolt there?
Page 12 and 13 show it very well. You did get into the wrong harness. The harness that leads to the center of the all the injector line outlets is the one you are after. In that two wire bundle, you want the one closer to the engine.
You do want the sensor at the inlet, yes. Hard to tell by the picture, but is there a tapped banjo bolt there?
And yes there is a sensor at the vp44 inline ...
Thread
Thread Starter
Forum
Replies
Last Post
justinsbeck
24 Valve 2nd Gen Dodge Cummins 98.5-02
6
01-18-2016 12:15 AM
Diesel Bombers
General Diesel Related
0
09-21-2015 06:10 PM
DeLuzGN
24 Valve 2nd Gen Dodge Cummins 98.5-02
5
03-17-2015 08:08 AM