conversion write-up 47re to nv4500
#22
well my truck does not have a cable, it is electronic.
so according to dodge, right now I have a speed sensor in the transmission. but once i put the manual tranny in, i will have to use the speed sensor/abs sensor in the diff.
so basically i have my factory wiring, and i need to know where to splice in the harness from the diff.
was your truck a manual truck from the factory or was it converted?
and does your truck have a speedo cable coming from the transfer? or a sensor in the diff?
thanks bud
so according to dodge, right now I have a speed sensor in the transmission. but once i put the manual tranny in, i will have to use the speed sensor/abs sensor in the diff.
so basically i have my factory wiring, and i need to know where to splice in the harness from the diff.
was your truck a manual truck from the factory or was it converted?
and does your truck have a speedo cable coming from the transfer? or a sensor in the diff?
thanks bud
#24
#25
Loading pics now, and it was there from factory. but here is some pics: This is goin from the transfer case to the motor
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
This is the bundle of wires that went to the auto trans. Thoses wires for the speed sensor is in with this bundle.
[IMG][/IMG]
Hard to see but the bundle hooks to a plate which that hooks to the back of the motor
[IMG][/IMG]
Then it all goes into one bundle
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
This is the bundle of wires that went to the auto trans. Thoses wires for the speed sensor is in with this bundle.
[IMG][/IMG]
Hard to see but the bundle hooks to a plate which that hooks to the back of the motor
[IMG][/IMG]
Then it all goes into one bundle
#26
#27
#28
I AM RIGHT IN THE MIDDLE OF THE CONVERSION, SO AS OF NOW I HAVE JUST REMOVED ALL THE FACTORY STUFF.
SO YOU JUST HOOKED UP, THE SPEEDO CABLE, AND THE NEUTRAL SAFETY SWITCH?
DOES YOUR SPEEDOMETER GAUGE WORK?
WHAT ABOUT REVERSE LIGHTS?
ONLY ASKING CAUSE THE DEALER SAID I WAS GOING TO HAVE TO FIGURE OUT HOW TO SPLICE IN THE ABS/ SENSOR IN THE DIFF OR MY SPEEDOMETER WOULD NOT WORK.
---AutoMerged DoublePost---
HEY
SO YOU JUST HOOKED UP, THE SPEEDO CABLE, AND THE NEUTRAL SAFETY SWITCH?
DOES YOUR SPEEDOMETER GAUGE WORK?
WHAT ABOUT REVERSE LIGHTS?
ONLY ASKING CAUSE THE DEALER SAID I WAS GOING TO HAVE TO FIGURE OUT HOW TO SPLICE IN THE ABS/ SENSOR IN THE DIFF OR MY SPEEDOMETER WOULD NOT WORK.
---AutoMerged DoublePost---
HEY
Last edited by wilson1207; 10-24-2010 at 01:41 PM. Reason: Automerged Doublepost
#29
I dont see why they dont you that. When i converted mine i used the donor truck transfer case which was gear 4.10 and mine was geared 3.55. So i had to switch the speedo gear and it just worked fine. On the neutral safety switch, theres a wire that is black with a white tracer you gotta ground that out because if you dont ground it out. the truck wont do nothing!
#30
OK SO I NEED TO CONNECT A GROUND TO THE BBLACK/WHITE WIRE.
YOUR TRANSFER LOOKS DIFFERANT THAN MINE, DID YOU PUT IN A 2ND GEN NV4500, OR THE FIRST GEN GETRAG TRANNY?
---AutoMerged DoublePost---
oh and do you have a pic of where your speedo cable is connected to the transfer case?
YOUR TRANSFER LOOKS DIFFERANT THAN MINE, DID YOU PUT IN A 2ND GEN NV4500, OR THE FIRST GEN GETRAG TRANNY?
---AutoMerged DoublePost---
oh and do you have a pic of where your speedo cable is connected to the transfer case?
Last edited by wilson1207; 10-24-2010 at 09:19 PM. Reason: Automerged Doublepost