Transfer Sled Pulling Diesel Discussions of Transfer Sled Pulling , Set Up , Designs , Practices , Techniques , Tips and More
*PLEASE DO NOT POST FUTURE EVENT DISCUSSIONS IN THIS SECTION*

Pulling my 06 dodge for the first time this weekend

Thread Tools
 
Search this Thread
 
Old May 4, 2010 | 06:18 AM
  #1  
commonrailcummins13's Avatar
Thread Starter
|
Diesel Fan
Joined: Jan 2010
Posts: 95
Likes: 3
From: Mount Joy, Pa
Default Pulling my 06 dodge for the first time this weekend

Im pulling my 06 Dodge 3500 this weekend for the first time. Ive pulled before but this is my first time with a manual tranny. Just looking to see if anyone has some thought on 4-high or 4- Low and what gear use suggest. any suggestions would help me greatly.
 
Reply
Old May 4, 2010 | 07:21 AM
  #2  
Diesel Dummy's Avatar
Diesel Bombers Sponsor
Joined: Mar 2007
Posts: 1,024
Likes: 51
From: Willet, N.Y.
Default

well you should have 410's for gears so 4th low is what i would try first, you should be fine with that with what you have done. If your clutch has been in a while then utilize it to its fullest potential, and rev and slowly let out to get you moving, just make sure you dont leave early before your rpm's are up so you stay under the turbo, but since its the stocker you should be just fine.

OH AND DONT WATCH YOUR PYRO!!!!!!!
 
Reply
Old May 4, 2010 | 09:02 AM
  #3  
96cummins06crd's Avatar
Diesel Fan
Joined: May 2010
Posts: 12
Likes: 0
From: Barrie On
Default

is your truck a 5.9 or a 6.7 ?
 
Reply
Old May 4, 2010 | 10:21 AM
  #4  
GetBlown5.9's Avatar
Diesel Wrench
Joined: Mar 2007
Posts: 586
Likes: 121
From: Baltimore, MD
Default

Originally Posted by commonrailcummins13
Im pulling my 06 Dodge 3500 this weekend for the first time. Ive pulled before but this is my first time with a manual tranny. Just looking to see if anyone has some thought on 4-high or 4- Low and what gear use suggest. any suggestions would help me greatly.
Mount Joy, Pa...would you be going to the buck?

Use 4th gear, 4-low range whether you have 4.10 or 3.73. its the best over all gear in the 6spd.

When you get hooked up to the sled point your drivers mirror so you can see your rear wheels.

Bring your rpms up to about 3500 and slowly but steadily start to let the clutch out, you will hear the motor start to load and the truck will begin to roll, watch your tire and about the time you make a full revolution you should be all the way off the clutch. You shouldnt slip it for more than about 3-5 seconds (it happens quick)

Here is a video so you can see about how far I let it roll before the clutch is all the way locked up.

 
Reply
Old May 4, 2010 | 01:12 PM
  #5  
94 12valve's Avatar
Diesel Bomber
Joined: Jan 2009
Posts: 3,504
Likes: 157
From: Pylesville, Maryland
Default

Originally Posted by GetBlown5.9
Mount Joy, Pa...would you be going to the buck?

Use 4th gear, 4-low range whether you have 4.10 or 3.73. its the best over all gear in the 6spd.

When you get hooked up to the sled point your drivers mirror so you can see your rear wheels.

Bring your rpms up to about 3500 and slowly but steadily start to let the clutch out, you will hear the motor start to load and the truck will begin to roll, watch your tire and about the time you make a full revolution you should be all the way off the clutch. You shouldnt slip it for more than about 3-5 seconds (it happens quick)

Here is a video so you can see about how far I let it roll before the clutch is all the way locked up.

YouTube - TJ Bates One Piece At A Time
This is the same great advise he gave me when I first started. Was good then and still good now
 
Reply
Old May 4, 2010 | 09:21 PM
  #6  
commonrailcummins13's Avatar
Thread Starter
|
Diesel Fan
Joined: Jan 2010
Posts: 95
Likes: 3
From: Mount Joy, Pa
Default

thanks guys i appreciate it yes im going to the buck. Its a 5.9 the 6.7 didnt start til 07. Ill give it a whirl with the advice yous gave me thanks again i appreciate it.
 
Reply
Old May 4, 2010 | 09:40 PM
  #7  
94 12valve's Avatar
Diesel Bomber
Joined: Jan 2009
Posts: 3,504
Likes: 157
From: Pylesville, Maryland
Default

i'll be up there arround noon and Tj will be there shortly after for a pre game cook out with quite a few other members. Feel free to come on up and hang out before and after the pulls.
 
Reply
Old May 4, 2010 | 09:46 PM
  #8  
iker42's Avatar
Diesel Enthusiast
Joined: Aug 2007
Posts: 288
Likes: 82
From: Christiana, PA
Default

dave, wanna throw an exhaust housing on my truck?? haha.
 
Reply
Old May 4, 2010 | 09:49 PM
  #9  
94 12valve's Avatar
Diesel Bomber
Joined: Jan 2009
Posts: 3,504
Likes: 157
From: Pylesville, Maryland
Default

bring it up and I'll guide you through it. It will all depend if the 4 mounting bolts will come loose. I'll be up there at noon the sooner you get there the better
 
Reply
Old May 4, 2010 | 11:13 PM
  #10  
commonrailcummins13's Avatar
Thread Starter
|
Diesel Fan
Joined: Jan 2010
Posts: 95
Likes: 3
From: Mount Joy, Pa
Default

alright if i get a chance to head there a little early i might just swing by if not i wont be there til four thirty or so. but im sure ill see yahs around either way.
 
Reply



All times are GMT -5. The time now is 05:49 AM.