Quad Cab Back Door Latch
#1
Quad Cab Back Door Latch
My passenger side back door outside latch is giving up the ghost.
Has anyone had the same problem? When you pull it out, it doesn't grab until the very last 1/8" of latch travel. It feels like something in there is slowly bending over time.
I have not taken the door panel off yet to look.
Does anyone have a diagram of the door latch mecahnism in there so I have something to compare it too?
Any input would be appreciated.
Thanks!
Has anyone had the same problem? When you pull it out, it doesn't grab until the very last 1/8" of latch travel. It feels like something in there is slowly bending over time.
I have not taken the door panel off yet to look.
Does anyone have a diagram of the door latch mecahnism in there so I have something to compare it too?
Any input would be appreciated.
Thanks!
#2
REMOVAL
INSTALLATION
Diagrams Attached
- Raise the window to the full up position.
- Remove the waterdam. Refer to Front Door panel.
- Disconnect the actuator rods.
- Remove the bolts. (Fig. 7)
- Disconnect the electrical connector and remove the latch.
INSTALLATION
- Connect the electrical connector and install the latch assembly.
- Install the bolts and tighten to 10 N.m (89 in.lbs) .
- Connect the actuator rods.
- Adjust the latch as needed.
- Install the waterdam.
- Locate access hole and remove the mylar tape covering it. (Fig. 8)
- Insert a 5/32-inch hex-wrench through hole and into adjustment screw. Loosen screw.
- Operate outside handle several times to release any restriction because of mis-alignment.
- Tighten adjustment screw to 3 N.m (30 in.lbs) .
- Test handle for proper operation.
Diagrams Attached
Last edited by DB Admin; 06-07-2008 at 10:26 AM.
The following users liked this post:
Marine (06-07-2008)
#3
DM,
Thanks for that, but that sounds like the front door. The quad cab window doesn't move up or down, it opens from the side and pops out on the trailing edge of the door.
I didn't think there was any electrical in the quad cab door.
Thanks!
Thanks for that, but that sounds like the front door. The quad cab window doesn't move up or down, it opens from the side and pops out on the trailing edge of the door.
I didn't think there was any electrical in the quad cab door.
Thanks!
#4
This is the Information i have under Rear Door Latch for 2nd Gen CTD's i seen the window down and ect and wonder4ed WTF my self but the adjustments and ect are correct
#5
INSIDE HANDLE ACTUATOR
Heres the INSIDE HANDLE ACTUATOR Info
REMOVAL
Heres the INSIDE HANDLE ACTUATOR Info
REMOVAL
- Remove the screw and remove the inside handle. (Fig. 5)
- Remove the door trim panel.
- Disconnect the latch actuator rod. (Fig. 6)
- Remove the nuts and remove the remote handle actuator.
- Install the remote handle actuator and install the nuts.
- Tighten the nuts to 10 N.m (89 in.lbs) .
- Connect the latch actuator rod.
- Install the door trim panel.
- Install the inside handle and install the bolt.
- Tighten the bolt to 9 N.m (80 in.lbs) .
#6
I will definitely have to do this when it stops raining. I hate not having a rear door on the passenger side.
Thanks DM!
Thanks DM!
#7
EXTERIOR HANDLE
Removal
Removal
- Remove the front glass run channel. Refer to Window Track.
- Disconnect the latch actuator rod. (Fig. 2)
- Remove the nuts and remove the handle.
- Install the latch and install the nuts.
- Connect the latch actuator rod.
- Install the front glass run channel. Refer to Window Track.