What else...
#1
What else...
What else can I do to make more power???
Right now running an M4 fuel pin, HE351VGT turbo which will be tuned in shortly, valve springs, low pressure piston lift pump, 3800 rpm spring, 4" exhaust, intercooler, BHAF. I don't know where else to go from here, besides maybe twins. I was thinking about a tubular exhaust manifold, which I will build when I get bored, but are there any other things I could try before that (twins or exhaust manifold).
Really looking to stay with the VE pump, I know the P pump would be where it's at, but I also have $28k of tuition to pay this semester, so that's not gonna happen.
---AutoMerged DoublePost---
Guess I am looking at the M&H dynamic timing spacer and smoke control device. We'll see how those work before doing anything else major.
Right now running an M4 fuel pin, HE351VGT turbo which will be tuned in shortly, valve springs, low pressure piston lift pump, 3800 rpm spring, 4" exhaust, intercooler, BHAF. I don't know where else to go from here, besides maybe twins. I was thinking about a tubular exhaust manifold, which I will build when I get bored, but are there any other things I could try before that (twins or exhaust manifold).
Really looking to stay with the VE pump, I know the P pump would be where it's at, but I also have $28k of tuition to pay this semester, so that's not gonna happen.
---AutoMerged DoublePost---
Guess I am looking at the M&H dynamic timing spacer and smoke control device. We'll see how those work before doing anything else major.
Last edited by mkriebs; 03-01-2013 at 07:10 AM. Reason: Automerged Doublepost
#4
I am on non-ic injectors, which injectors would be an upgrade?
---AutoMerged DoublePost---
P-pump is unfortunately not in the budget right now. If i were to go P-pump, I would go twins as well, though.
---AutoMerged DoublePost---
P-pump is unfortunately not in the budget right now. If i were to go P-pump, I would go twins as well, though.
Last edited by mkriebs; 03-02-2013 at 09:29 AM. Reason: Automerged Doublepost
#6
This is the VGT version, so I could get more injector in without the EGT's going sky high. It opens up to a 25mm housing, IIRC.
#8
Rocken Tech 14mm head and rotor, or 14mm Scheid pump, Intake, exhaust with 4-inch DP, fuel pin, 5x25 injectors, 66/74/14 turbo, or HX35/71mm twins, 1 tooth skipped on timing (c.22 deg), 3,200rpm or 3,800rpm springs, 60 pound valvesprings, head studs, o-rings, gauges, 150+gph lift pump with draw straw and filters, loctite front pump seal and 30psi inlet pressure. 800-900hp with nitrous.
The following users liked this post:
mkriebs (03-03-2013)
#9
Rocken Tech 14mm head and rotor, or 14mm Scheid pump, Intake, exhaust with 4-inch DP, fuel pin, 5x25 injectors, 66/74/14 turbo, or HX35/71mm twins, 1 tooth skipped on timing (c.22 deg), 3,200rpm or 3,800rpm springs, 60 pound valvesprings, head studs, o-rings, gauges, 150+gph lift pump with draw straw and filters, loctite front pump seal and 30psi inlet pressure. 800-900hp with nitrous.
Also, any more info on the pump and how it works being a DD?
I have the exhaust and fuel pin already, as well as the 3,800 spring, valve springs, studs and o-rings. So I am pretty well on my way.