--mods, mods, mods!--
#11
#14
i know we sound like a broken record but a lift pump is one of the very first things that need upgraded on a vp44 truck. yes there a lil pricey, but its better than the 1500+ it would cost to get a new stock lift pump, vp44 and labor if your stock lp goes out.
the smarty dont add much by there selfs in the second gens. when there stacked is when the smarty comes alive with the vp44.
i would go with the adrenaline w/ pulse monitor or the edge juice with attitude.
another very weak point in your setup is the stock TC. i tore mine up with just a set of rv injectors which are just a 40 hp injector. if your easy on it they will hold for awhile, but if u drive a vehicle hard, u might look into upgrading the TC before the performance
good luck with it all and welcome to db
the smarty dont add much by there selfs in the second gens. when there stacked is when the smarty comes alive with the vp44.
i would go with the adrenaline w/ pulse monitor or the edge juice with attitude.
another very weak point in your setup is the stock TC. i tore mine up with just a set of rv injectors which are just a 40 hp injector. if your easy on it they will hold for awhile, but if u drive a vehicle hard, u might look into upgrading the TC before the performance
good luck with it all and welcome to db
#17
I just posted this on another thread, but I think it's good enough to repeat...
bomb'ing" your truck is a very slippery slope, and you can easily find yourself in a cycle of modd'ing one part which in turn causes a weakness in another area. For example... your 24 valve Cummins is a VERY VERY VERY SOLID platform with a VERY VERY VERY SORRY (and expensive) injection pump.
I FULLY SUPPORT increasing the power of these motors... and I FULLY SUPPORT doing it RIGHT.
In my humble opinion, here's my prescription for more power - RELIABLY.
1. Fix Fuel Supply System -> FASS, Raptor, AirDog
2. Increase Airflow -> BHAF or aftermarket intake
3. Get the air out -> 4" exhaust
4. Add some way to monitor your Pressure's and EGT's - I suggest Edge or Quadzilla for 99% of applications
5. Add some POWER! ->The same Edge or Quadzilla "box,chip,tuner" suggested above
6. For Mo' Powah, you could drop in a set of mild injectors -> RV275's or one of the many 65hp injectors.
That's should be good for about a 100hp bump and over a couple hundred ft/lbs of tq over stock. Anything over that and you'll need to look at things like bigger turbo's, bigger injectors, etc.
The cost of all this is around $1500. Cheaper than the cost of a quality injector pump or turbo or long block. Just adding a "box,chip,puck,tuner" could easily cause the failure of any one of the aforementioned parts...
If you do it... do it right.
BTW. THANK YOU FOR YOUR SERVICE SIR!!!!!!!!!
Read more: https://www.dieselbombers.com/5-9l-2...#ixzz0hK5zFejx
bomb'ing" your truck is a very slippery slope, and you can easily find yourself in a cycle of modd'ing one part which in turn causes a weakness in another area. For example... your 24 valve Cummins is a VERY VERY VERY SOLID platform with a VERY VERY VERY SORRY (and expensive) injection pump.
I FULLY SUPPORT increasing the power of these motors... and I FULLY SUPPORT doing it RIGHT.
In my humble opinion, here's my prescription for more power - RELIABLY.
1. Fix Fuel Supply System -> FASS, Raptor, AirDog
2. Increase Airflow -> BHAF or aftermarket intake
3. Get the air out -> 4" exhaust
4. Add some way to monitor your Pressure's and EGT's - I suggest Edge or Quadzilla for 99% of applications
5. Add some POWER! ->The same Edge or Quadzilla "box,chip,tuner" suggested above
6. For Mo' Powah, you could drop in a set of mild injectors -> RV275's or one of the many 65hp injectors.
That's should be good for about a 100hp bump and over a couple hundred ft/lbs of tq over stock. Anything over that and you'll need to look at things like bigger turbo's, bigger injectors, etc.
The cost of all this is around $1500. Cheaper than the cost of a quality injector pump or turbo or long block. Just adding a "box,chip,puck,tuner" could easily cause the failure of any one of the aforementioned parts...
If you do it... do it right.
BTW. THANK YOU FOR YOUR SERVICE SIR!!!!!!!!!
Read more: https://www.dieselbombers.com/5-9l-2...#ixzz0hK5zFejx
The following users liked this post:
cummins24 (03-06-2010)
#18
If I was gonna start all over here is my list. I went through most of the stuff I could when mine still had the VP44. Most of the exact mods I would recommend would be on what you would use the truck for and what your realistic HP goals are. For a fun 400hp street truck you dont need much but the basics and maybe a little more than what I have listed below.
Guages
lift pump
exhaust/intake
tourque converter/valve body
Chip or programmer
turbo/injectors
Guages
lift pump
exhaust/intake
tourque converter/valve body
Chip or programmer
turbo/injectors
Last edited by 2141pete; 03-07-2010 at 04:00 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Spaky6.0mudder
Ford Powerstroke 03-07 6.0L
7
08-03-2015 08:54 PM
rtbcoop
12 Valve 2nd Gen Dodge Cummins 94-98
0
12-30-2014 02:13 AM