"Wait to Start" light
#12
I have put about 40 miles on with the smarty tune on the truck and beat foot down the highway doing well over 60mph in places where the lamp would normally come on. But so far it's looking good! And I hope it stays as such! I only run the smarty on #3 most of the time weather I'm towing or not and god I missed the power! I have yet to hook up to my trailer and try it but I can usually get the lamp to come on without so I'm keeping my fingers crossed!
Now if I can only get my a/c to work I'd be set! Lol
But again, thanks for the help and will keep ya updated!
Now if I can only get my a/c to work I'd be set! Lol
But again, thanks for the help and will keep ya updated!
#16
i have a 2005 dodge ram 3500 4x4 quad cab diesel automatic that purchased 4 months ago and just before i bought it the prvious owners had cummins put all new injectors in and had the overhead done on it.it had 190000 on it when i bought it now has 194000.i was pulling my trailer with a ranger on it saturday and came down a hill and i took my foot off the throttle in tow/haul mode and it geared down then i heard a chime the dinged 10 times and my wait to start light came on and will not go off.had one code of p1222 when i scanned it with my scanner only in freeze frame with the actron scanner.what is the problem feels like it doesnt have as much power and the wait to start light will not go off.truck is stock.please help.
#17
Your Vehicle: 2005 Dodge or Ram Truck RAM 2500 Truck 4WD L6-5.9L DSL Turbo VIN C
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P1222
P1222
P1222-LEAK DETECTION DURING MOTORING
NOTE: For a complete wiring diagram, refer to Diagrams/Electrical .
When engine is motoring (i.e. Engine is running, but requires no fuel injection) the only required fuel delivery to the rail is due to natural leakage in the system. The natural leakage depends directly on the rail pressure. A definite amount of fuel is required to overcome the natural leakage, for different fuel pressures. The Engine Control Module (ECM) sets Leakage Detected, when the fuel flow exceeds an expected value. When a leak is detected in the system, a counter is initiated. When the counter reaches a predetermined value a fault is set and engine derate is enabled. When the leak is not detected the counter counts down, and once the counter becomes zero the engine is set back to normal running conditions.
When Monitored: Engine is motoring and at operating temperature with no fuel system and engine speed related DTCs.
Set Condition: Counter reaches a calibrated value.
Possible Causes
NOTE: Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. See: Powertrain Management\Computers and Control Systems\Testing and Inspection\Initial Inspection and Diagnostic Overview\Initial Inspection
OTHER DTCs PRESENT
Turn the ignition on.
With the scan tool, select View DTCs. Are there any other fuel system related DTCs present along with this DTC?
Yes
Perform the diagnostics for the other fuel system DTCs before proceeding.
No
Perform the INJECTOR RETURN FLOW TEST procedure. See: Powertrain Management\Comput
---AutoMerged DoublePost---
Smarty will hide code p1222. wait to start light and chime usually means code p1222
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P1222
P1222
P1222-LEAK DETECTION DURING MOTORING
NOTE: For a complete wiring diagram, refer to Diagrams/Electrical .
When engine is motoring (i.e. Engine is running, but requires no fuel injection) the only required fuel delivery to the rail is due to natural leakage in the system. The natural leakage depends directly on the rail pressure. A definite amount of fuel is required to overcome the natural leakage, for different fuel pressures. The Engine Control Module (ECM) sets Leakage Detected, when the fuel flow exceeds an expected value. When a leak is detected in the system, a counter is initiated. When the counter reaches a predetermined value a fault is set and engine derate is enabled. When the leak is not detected the counter counts down, and once the counter becomes zero the engine is set back to normal running conditions.
When Monitored: Engine is motoring and at operating temperature with no fuel system and engine speed related DTCs.
Set Condition: Counter reaches a calibrated value.
Possible Causes
NOTE: Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. See: Powertrain Management\Computers and Control Systems\Testing and Inspection\Initial Inspection and Diagnostic Overview\Initial Inspection
OTHER DTCs PRESENT
Turn the ignition on.
With the scan tool, select View DTCs. Are there any other fuel system related DTCs present along with this DTC?
Yes
Perform the diagnostics for the other fuel system DTCs before proceeding.
No
Perform the INJECTOR RETURN FLOW TEST procedure. See: Powertrain Management\Comput
---AutoMerged DoublePost---
Smarty will hide code p1222. wait to start light and chime usually means code p1222
Last edited by kylemckay; 01-17-2013 at 09:45 PM. Reason: Automerged Doublepost
#18
thanks just got it checked at dealer and $300 later found out two injectors are bad.dealer wants 2800 to fix it.just picked it up and taking it somewhere else.bad thing is when i bought it it had new in jectors put in it buy cummins,so i contacted them and told them it only has 5000 miles on injectors and they said there is no warranty.aint that something.they making crap that cost $680 each and had all 6 put in and did not last.
#19
thanks just got it checked at dealer and $300 later found out two injectors are bad.dealer wants 2800 to fix it.just picked it up and taking it somewhere else.bad thing is when i bought it it had new in jectors put in it buy cummins,so i contacted them and told them it only has 5000 miles on injectors and they said there is no warranty.aint that something.they making crap that cost $680 each and had all 6 put in and did not last.