02 Cummins acts like it is not geting fuel when pedal is pressed
#1
02 Cummins acts like it is not geting fuel when pedal is pressed
I did a 5 min search but didnt find anyone with the exact same problems so decided to ask, my 5.9l 2002 dodge ram 2500 cummins with a 47re is trowing codes I keep clearing them and as soon as I start the truck they come back. My codes are p0121 p0122 p0222 p0236, I've looked them up but I dont know what I'm looking at . someone smarter than me please help, I put a new timbo apps in with in the past month to get rid of the p0122 code I was getting. It stopped for a month and ran fine than started doing this, I also have a new fuel filter I put in at the same time. It feels like the truck is not getting any fuel as soon as I press the pedal, but idles fine, I'm hoping its not the vp44 thanks for any help you can give.
Casper
Casper
#2
Are there any modifications done to the truck and engine? Please list any that are done.
---AutoMerged DoublePost---
P0236 is an over boost code, the rest are all related to the APPS. When the new APPS was installed was it rester?
---AutoMerged DoublePost---
P0236 is an over boost code, the rest are all related to the APPS. When the new APPS was installed was it rester?
Last edited by RAW; 10-03-2010 at 10:06 AM. Reason: Automerged Doublepost
#3
#7
when I put a volt meter on the apps it goes from .609v to 4.v smoothly is there some other test to do?
Thanks
Casper
---AutoMerged DoublePost---
almost forgot i did do an apps rewire a wile back, the one where you tap the wire at the apps and run it to the pcm
Thanks
Casper
---AutoMerged DoublePost---
almost forgot i did do an apps rewire a wile back, the one where you tap the wire at the apps and run it to the pcm
Last edited by Lilcasper888; 10-03-2010 at 10:30 AM. Reason: Automerged Doublepost
#8
You can try a reset, no promises though.
-Disconnect batteries for a 1/2 hour, then reconnect.
-Turn key to run, but DON NOT start
_Depress pedal all the way to the floor, and then bring back up. Do both motions taking about 3 seconds to complete the travel each way
-Key to off, then run as normal.
This teaches, or relearns the the position and travel of the APPS into the computer.
---AutoMerged DoublePost---
Care to explain that one a bit more?
-Disconnect batteries for a 1/2 hour, then reconnect.
-Turn key to run, but DON NOT start
_Depress pedal all the way to the floor, and then bring back up. Do both motions taking about 3 seconds to complete the travel each way
-Key to off, then run as normal.
This teaches, or relearns the the position and travel of the APPS into the computer.
---AutoMerged DoublePost---
almost forgot i did do an apps rewire a wile back, the one where you tap the wire at the apps and run it to the pcm
Last edited by RAW; 10-03-2010 at 10:33 AM. Reason: Automerged Doublepost
#9
I'll go do that now, and come back in about an hour to give an update.
Thank you
Casper
---AutoMerged DoublePost---
http://www.suncoastconverters.com/im...d%20rewire.pdf
http://www.suncoastconverters.com/im...oundrewire.pdf
I hope this link works
Thank you
Casper
---AutoMerged DoublePost---
http://www.suncoastconverters.com/im...d%20rewire.pdf
http://www.suncoastconverters.com/im...oundrewire.pdf
I hope this link works
Last edited by Lilcasper888; 10-03-2010 at 10:36 AM. Reason: Automerged Doublepost