600 for a chip? the chip new is no even 600 bucks man or do you mean 600 for the fass and chip?

 

I have the adaptor that goes from triangle to flat.

 

That pump is an HD series (used to be called a 150 series) and is a 95 gph pump. EM-1001 is the part number for the smaller motor that is used on the low pressure 95 and 150 gph pumps. I can't read the serial number off the silver tag above the fuel filter though. That would tell me exactly what that pump was built as and what pressure it was set to when we built it. If you can get that for me I can look it up for you.

 

13686

 

id be ready to kick someones butt. did you see pictures before you bought it?

 

The pump is a FASS 150/95-1008 (HD Series 95gph made for 98.5-04 Cummins) It was made 11/2/07. 16-18 psi

---AutoMerged DoublePost---

Here are some filter cross references to help get you some new ones:
Fuel Filter (1 1/2-16)
Baldwin BT372-10 (5M)
Baldwin BT372-MPG (10M)
Carquest 85724 (10M)
Caterpillar 3T8642(5M)
Cim-Tek 70032 (10M)
Cim-Tek 70213 (3M)
Donaldson P550705 (10M)
Donaldson P569381 (3M)
FASS FF1003 (Cim-Tek)
FASS FF1010 (Cim-Tek)
Fleetguard FF5588 (10M)
Fleetguard HF 6338 (10M)
FLEETGUARD HF 6601 (10M)
FLEETGUARD HF 6604 (3M)
FLEETGUARD HF 6607 (6M)
Fram P8024 (5M)
Hastings HF779 (5M)
Luber Finer LFH4922
Luber Finer LFH8324
Purolator 7400SAL032F2 (3M)
Wix 51116 (11M)
Wix 51120 (9M)
Wix 51202 (5M)
Wix 51724(10M)
Wix A07A03C (3M)

Water Seperator (1-14)
Baldwin BF 1258 (10M)
Baldwin BF1212 (20M)
Baldwin BF1214
Baldwin BF7546 (10M)
CAT 1752949(3M)
Donaldson P551000 (10M)
Donaldson P551001(10M)
Donaldson P558000 (20M)
Fleetguard FS-1000 (10M)
Fleetguard FS-1001 (10M)
Fleetguard FS-1009(14M)
Fleetguard FS-1023 (144M)
Fleetguard FS-1212(14M)
Fleetguard FS1282 (14M)
LuberFiner LFF8000
LuberFiner LFF8011
LuberFiner LFF8020
Motorcraft FD818 (14M)
Wix 33405(14M)
Wix 33406 (14M)
Wix 33407 (5M)
Wix 33522 (10M)

 

This is so awesome!!! Thank-you. I run it the other day and seems to have lots of flow. Can't wait to install. A friend of mine is a Cummins mechnic and has offered his help. We plan to take the box off the truck. I already have a new WS and the FF is on order. I plan to wait until the weather gets better and install the Juice box at the same time. Can I increase the pressure if needed. Shim the spring? install a new one???

---AutoMerged DoublePost---

Can I or should I go through my stock filter housing using my fuel heater?