1st Generation Dodge Cummins 89-93 Discussion of 12 Valve 5.9 Liter Dodge Cummins Diesels with Rotary Injection Pumps

help !!!!!!!!

Thread Tools
 
Search this Thread
 
  #1  
Old 11-05-2010, 03:51 PM
92 diesel lover's Avatar
Diesel Fan
Thread Starter
Join Date: Oct 2010
Location: selinsgrove PA
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default help !!!!!!!!

Well Ijust installed new injector pump new injectors new lift pump new fuel filter truck still runs like crap I have a 92 intercooled diesel seems to idle fine till ya put it in gear then with truck in gear exhaust temps start to climb and starts runnin rough ,bled injectors. one thing I did notice is the ehaust temps at the back of truck seem warm I have dual3 inch pipes runnin 3/4 way back to bumper also doesent seem to be as much air (exhaust ) coming outta the pipes I am startin ta think bad turbo what do you guys think (I also adjusted valves) they were pretty good some one musta already did that. oh yea the truck has 193000 on her ran great before this after every thing I have done IT still runs as before I started workin on it an that sucks!!!!
 
  #2  
Old 11-05-2010, 04:34 PM
Thekingrulz69's Avatar
Diesel Fan
Join Date: Jun 2010
Location: SW Colorado
Posts: 92
Likes: 0
Received 1 Like on 1 Post
Default

try getting your valves adjusted. You could also have a timing issues, but i doubt it. I say valve adjust. And you do have good clean diesel in there right?
 
  #3  
Old 11-05-2010, 04:37 PM
prison's Avatar
Diesel Bomber
Join Date: Oct 2010
Location: Childress,TX
Posts: 1,150
Received 29 Likes on 27 Posts
Default

he said he adjusted the valves. assuming he did it right
 
  #4  
Old 11-05-2010, 04:39 PM
92 diesel lover's Avatar
Diesel Fan
Thread Starter
Join Date: Oct 2010
Location: selinsgrove PA
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

I adjusted valves and yes clean fuel......

---AutoMerged DoublePost---

adjusted according to service manual
 

Last edited by 92 diesel lover; 11-05-2010 at 04:39 PM. Reason: Automerged Doublepost
  #5  
Old 11-05-2010, 04:41 PM
prison's Avatar
Diesel Bomber
Join Date: Oct 2010
Location: Childress,TX
Posts: 1,150
Received 29 Likes on 27 Posts
Default

if you rev it can you hear the turbo spool?
 
  #6  
Old 11-05-2010, 04:47 PM
92 diesel lover's Avatar
Diesel Fan
Thread Starter
Join Date: Oct 2010
Location: selinsgrove PA
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

pulled air cleaner hose off seems like its spinnin ,I also pulled intake hose off (intercooler) pushes air out if you cover hose with your hand doesent build pressure till ya rev it hard
 
  #7  
Old 11-05-2010, 04:49 PM
RSWORDS's Avatar
BOMBARDIER

Join Date: Mar 2007
Location: Gloucester, VA
Posts: 11,159
Received 918 Likes on 537 Posts
Default

with the engine off remove the inlet to the turbo, check for shaft play, should b every little up/down left/right play and NO in and out. Next give it a spin should spin easy and spin for a little after you let go.
 
  #8  
Old 11-05-2010, 05:18 PM
92 diesel lover's Avatar
Diesel Fan
Thread Starter
Join Date: Oct 2010
Location: selinsgrove PA
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

side to side movment yes little if no in and out ....

---AutoMerged DoublePost---

with old pump I turned up fuel screw and only could get 15 pounds of boost new(rebuilt) pump I only have about 10lbs..is this normal

---AutoMerged DoublePost---

the turbo spins freely by hand and continues afterwards
 

Last edited by 92 diesel lover; 11-05-2010 at 05:18 PM. Reason: Automerged Doublepost
  #9  
Old 11-05-2010, 05:42 PM
Thekingrulz69's Avatar
Diesel Fan
Join Date: Jun 2010
Location: SW Colorado
Posts: 92
Likes: 0
Received 1 Like on 1 Post
Default

what power pin are you using? is it the stock cone or aftermarket?
 
  #10  
Old 11-05-2010, 05:46 PM
92 diesel lover's Avatar
Diesel Fan
Thread Starter
Join Date: Oct 2010
Location: selinsgrove PA
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

stock pin tryed a dennys 2 pin no diff for problem
 



All times are GMT -5. The time now is 02:38 AM.