12 Valve 2nd Gen Dodge Cummins 94-98 Discussion of 12 Valve 5.9 Liter Dodge Cummins Diesels with P7100 Injection Pumps

front driveshaft

Old Oct 30, 2010 | 02:19 PM
  #1  
cummins95's Avatar
Thread Starter
|
Diesel Wrench
Joined: Apr 2009
Posts: 772
Likes: 48
From: Sullivan County, PA
Default front driveshaft

anybody know the difference in lengths front manual to auto? i swapped an nv4500 into my truck n haven't gotten a front driveshaft for it. went out cruisin last night n almost couldnt pull out a stuck 2wd s10 time to cut mine down....
 
Reply
Old Oct 30, 2010 | 05:45 PM
  #2  
fivepointohno's Avatar
Diesel Fan
Joined: Oct 2010
Posts: 85
Likes: 6
From: central texas
Default

I think is 3in total 1 1/2 shorter for the front and 1 1/2 longer for the rear
 
Reply
Old Oct 30, 2010 | 06:02 PM
  #3  
cummins95's Avatar
Thread Starter
|
Diesel Wrench
Joined: Apr 2009
Posts: 772
Likes: 48
From: Sullivan County, PA
Default

got ahold of my buddy that has one n i measured it, i came up with 5 1/2 inches of difference. got er cut down n welded up, gonna put it in n give it a try. worst case scenario i end up buyin a driveshaft
 
Reply
Old Oct 31, 2010 | 06:02 AM
  #4  
fivepointohno's Avatar
Diesel Fan
Joined: Oct 2010
Posts: 85
Likes: 6
From: central texas
Default

damn sorry about that i was way off
 
Reply
Old Oct 31, 2010 | 08:40 AM
  #5  
cummins95's Avatar
Thread Starter
|
Diesel Wrench
Joined: Apr 2009
Posts: 772
Likes: 48
From: Sullivan County, PA
Default

haha no problem. i put it in last night, it aint pretty but it'll get me thru for right now. im gonna have to buy one anyway, it kinda spins in an oval now

i managed to burn all the hair off my arm when we were buildin it, i failed to see the 50 feet of waterproof fuse hangin off the bench in front of where i was grindin. all i saw was 2 foot flames on the bench so i grabbed it n threw it on the garage floor, so my right arm is bald now haha

---AutoMerged DoublePost---

yesterday while we were in the process of fixin my truck n tryin to burn down the garage, my friend pointed out that my front axel is not centered, it sticks out further on the drivers side, im assuming this is from the 2.5" lift + the stock track bar. i was lookin at the adjustable one from thuren fabrication, can anybody give me any insight on these? price aint too bad, just wonderin if its gonna last
 

Last edited by cummins95; Oct 31, 2010 at 08:40 AM. Reason: Automerged Doublepost
Reply
Old Oct 31, 2010 | 11:07 AM
  #6  
dan33klein's Avatar
Diesel Bomber
iTrader: (-1)
Joined: Nov 2008
Posts: 1,019
Likes: 11
From: cherry,il
Default

look at a dt profab trackbar
 
Reply
Old Oct 31, 2010 | 05:46 PM
  #7  
Dirt_Diver's Avatar
Diesel Enthusiast
Joined: Sep 2010
Posts: 260
Likes: 5
From: Funny farm
Default

When i swapped the nv4500 in mine i actually used the front driveshaft off of the donor truck which was the dually 5speed but then again too i also used the transfercase but there should be no difference bc their both the same tranfercases except one has a pto in it.
 
Reply
Old Oct 31, 2010 | 07:19 PM
  #8  
cummins95's Avatar
Thread Starter
|
Diesel Wrench
Joined: Apr 2009
Posts: 772
Likes: 48
From: Sullivan County, PA
Default

the front driveshaft was the only thing i didnt get with my donor truck. i put the welds to the test today n they held, just wont be able to run 4x4 down the road.
 
Reply
Old Nov 1, 2010 | 06:31 AM
  #9  
Heavy Smoker's Avatar
Diesel Fan
Joined: Sep 2010
Posts: 67
Likes: 1
From: Lockport NY
Default

It problably makes your whole truck shake now.
 
Reply
Old Nov 1, 2010 | 05:49 PM
  #10  
cummins95's Avatar
Thread Starter
|
Diesel Wrench
Joined: Apr 2009
Posts: 772
Likes: 48
From: Sullivan County, PA
Default

im not gonna run 4x4 down the road til i get a new driveshaft, just like to have it if i absolutely need it, or wanna play around like this
haha
 
Reply

Thread Tools
Search this Thread

All times are GMT -5. The time now is 09:49 PM.