Taking some time off this week and working on the truck. Yesterday was "Rear Door Day". I started by pulling the power window regulator assemblies out and cleaning the inside surfaces of the doors (inner skin where door panel mounts, and inside of outer skin as well).

https://www.strictlydiesel.com/denni...0/img_2485.jpg

Then I changed out the power lock actuators and installed new outer door handles with Jimmy Jammers. Sorry, no pics, didn't seem interesting enough.

Then I put in my sound deadening, on both the inner door skin as well as the inside of the outer door skin.

https://www.strictlydiesel.com/denni...0/img_2487.jpg

After installing the New OE power window regulator assemblies, reinstalling the OE vapor barrier and buttoning up the door panel, I installed new (updated) OE weatherstripping on the door opening and upgraded the door strikers to the Mustang units with the rubber bumpers.

https://www.strictlydiesel.com/denni...0/img_2489.jpg

The difference in sound when you close the door is so noticeable! I will get to the front doors later this week. It will be nice to have all of the windows and locks working right again, and the sound deadening is such a nice upgrade. Eventually I will make the time to gut the rest of the interior, pull the dash and sound deaden the rest of the cab.

Finally finished the front doors. Same deal as the rears, new OE lock actuators, new OE window regulator assemblies, everything cleaned and sound deadening added to the outer and inner surfaces. Fronts also got rear door handles without lock cylinders, Jimmy Jammers, Mustang strikers and new weatherstripping (not pictured). No real new info here, just pictures of the front door work.

https://www.strictlydiesel.com/denni...0/img_2511.jpg

https://www.strictlydiesel.com/denni...0/img_2512.jpg

https://www.strictlydiesel.com/denni...0/img_2513.jpg

So, it would appear that my CCV setup will need some additional work. I do think this engine is a bit tired, but it hasn't been worth the time to actually compression test it. It does have a miss that isn't injectors, wiring or IDM. I guess I will reserve judgement on the CCV setup until I get a fresh bullet in place.

https://www.strictlydiesel.com/denni...0/img_2520.jpg
The canister is catching some oil. This is about 3000 miles worth.

https://www.strictlydiesel.com/denni...0/img_2524.jpg
The problem is, it is still allowing enough of it to make it back up to the intake. No way to really know how much, but enough to be visible.

The canister is mounted down low, behind the drivers front tire. There's a good 3-4' of hose down and then back up. I was really hoping that this would be enough hose and a good enough canister setup to do a better job than this.

Could be that the canister is too small. Could be that running both valve covers to one canister is too much for it. Could be that this old turd has more blowby than this setup can efficiently handle. At some point I will need to remove the charge air tubes, it will be interesting to see how much oil is making it to those.

Not the best update, but all I've got for now.

Finally got around to swapping out the transmission. I had kept the fully built John Wood unit from my race truck, so now my old dinosaur has a trans that cost me almost as much as I paid for the truck! Oh well, one less thing to worry about. We do have to fine tune the VB as the shifting is a bit firm for a low power street truck (was previously behind a compound turbo'd, twin pump, 400cc setup).

https://www.strictlydiesel.com/denni...0/img_2606.jpg
Was a good time to check out the up-pipes for leaks and tighten a few loose exhaust manifold bolts.

https://www.strictlydiesel.com/denni...0/img_2607.jpg
This flexplate was on its way out, glad I got to it before it broke.

https://www.strictlydiesel.com/denni...0/img_2609.jpg
Billet flexplate from the race truck took care of the impending failure nicely!

https://www.strictlydiesel.com/denni...0/img_2608.jpg
Out with the old...

https://www.strictlydiesel.com/denni...0/img_2610.jpg
In with the...er...somewhat new!

Will have to pull the VB apart some weekend and see which way it is setup. We changed it so many times due to adding nitrous, removing nitrous, etc...who the heck remembers how it's setup now. I was hoping that the TC would have a bit higher stall, but apparently I had too much taken out of it when I had it refreshed (it was a lot higher in the race truck, so I had some taken out for the street build...probably should have left it alone). No biggie, will just have to pull it and have it restalled again later if I decide I'm not happy with it.

I got my hands on a decent 08-10 Tailgate in the right color. Looks much nicer than the beat up stocker! I tried using the Tailgate Handle Backup Camera in my stock tailgate, but the quality of that piece was horrible and the handle wouldn't stay in place when you used it to open the tailgate. The 08-10 Tailgate Handle with Backup Camera is much nicer, and it stays put (so far).

I also installed a power tailgate lock from Pop-N-Lock and a Jimmy Jammers tailgate guard while I was at it. Sorry, no pictures of those. The wiring for the camera and lock were the worst part, as both had to go inside the cab, but to 2 different places.

https://www.strictlydiesel.com/denni...0/img_2633.jpg
08-10 Tailgate - Used But Looks Good

https://www.strictlydiesel.com/denni...0/img_2634.jpg
Amazon Tailgate Handle with Backup Camera

https://www.strictlydiesel.com/denni...0/img_2635.jpg
View From Backup Camera on Double DIN Kenwood Head Unit

The camera is certainly a "nice to have" when you back into just about everywhere you park. The angle of this one is good, I can tell when I'm right up on a wall or tree, or getting close to the nose of a car.

This weekend...have to tear into the valve body and see what we've got. Definitely setup for more power than this truck is making!

I just realized that I have a truck update that I totally forgot about. I actually haven't had much time to work on the truck lately, due to other projects (personal and work related). I did manage to get my headlight upgrade installed a few weeks ago though, I just spaced posting the updates here when I did it.

The factory 05-07 headlights look OK, but the lighting sucks, even with upgraded bulbs. Having had Projector HIDs in the past, I knew that was what this thing needed. I ordered a set of brand new OEM headlights from Ford and shipped them off to Dan Cordoba of DC Customs for all of the upgrades (see list below). Dan did a Killer Job on these, I couldn't be happier!

-G5-BRT Projectors
-Osram CBB D2S Bulbs
-Apollo 2.0 Flat Shrouds
-Oxford White and Black paint
-Tinted Klearz Reflector
-XD Xtreme Digital Ballasts
-DC Customs H13 Harness
-XD Ceramic 3157 Switchback Park/Turn Indicators

https://www.strictlydiesel.com/denni...0/img_2940.jpg
Headlights Installed - Close Up

https://www.strictlydiesel.com/denni...0/img_2939.jpg
Headlights Installed

https://www.strictlydiesel.com/denni...0/img_2941.jpg
Headlights Installed

https://www.strictlydiesel.com/denni...0/img_2932.jpg
Standard Bulb (Left) vs Projector HID (Right) - This is LOW BEAM ONLY (notice the nice cutoff on the top of the HID)

Here's a link to the DC Customs post on Facebook with a few more pictures of Dans work on my lights. Check him out if you are in the market for some light work!

This update is SOOOOOO LOOOONNNNGGGGG overdue. I've been referring to this as "The Longest Stereo Install Ever" (that isn't some kind of crazy, high end, show build). Anyway, a quick bit about the system and then TONS OF PICTURES. Sorry for the length of this, I have it split into multiple posts.

System Consists of:
Kenwood DNX-696S Double DIN Head Unit (custom mount)
Zapco ASP-Q1 Pre-Amp/Crossover (custom mount in AC controls location)
Rockville 50 Farad Capacitor
(2) Old School Orion 2150GX Amps (600W ea)
(2) Old School Orion 400BDG Bridging Modules
(3) Old School Orion 280GX Amps (160W ea)
(2) JL Audio 10TW3-D8 Subs (custom sealed enclosure)
(2) Sets a/d/s/ A6is Component Sets (front stage)
- (4) Total 6.5" Midbass (2/door)
- (4) Total 1" Soft Dome Tweeter (1/door + 1/pillar)
(1) Set Pioneer TS-D68F 6x8 Direct Fit Speakers (rear fill)
2/0 Custom Battery/Starter/Alternator/Ground Cables
DC Power 370A Alternator

https://www.strictlydiesel.com/denni...0/img_3093.jpg
Gutting The Interior for Sound Deadening

https://www.strictlydiesel.com/denni...0/img_3094.jpg
More Gutting...

https://www.strictlydiesel.com/denni...0/img_3095.jpg
Expanding Foam Used (carefully) in Key Places (the roof is solid and tight now)

https://www.strictlydiesel.com/denni...0/img_3110.jpg
Roof Getting CLD.

https://www.strictlydiesel.com/denni...0/img_3111.jpg
Back Wall of Cab Getting CLD.

https://www.strictlydiesel.com/denni...0/img_3126.jpg
Roof Getting a Sound Blocking Type Product (can't say if MLV or other)

https://www.strictlydiesel.com/denni...0/img_3127.jpg
I used Tons of Tesa Tape on OEM and other Harnesses

https://www.strictlydiesel.com/denni...0/img_3144.jpg
While I had Easy Access, I Installed some S&B Body Mounts

https://www.strictlydiesel.com/denni...0/img_3146.jpg

https://www.strictlydiesel.com/denni...0/img_3149.jpg

https://www.strictlydiesel.com/denni...0/img_3157.jpg
Dash on the Stand for Repairs, Security System and Audio Work

https://www.strictlydiesel.com/denni...0/img_3158.jpg
Bare Firewall Ready for CLD

https://www.strictlydiesel.com/denni...0/img_3170.jpg
Firewall Covered in CLD (OEM Pad was Reinstalled Over the CLD)

https://www.strictlydiesel.com/denni...0/img_3171.jpg
Dash Mount Tabs Covered in Tesa Tape

Continued in next post...

Continued from Previous Post...

https://www.strictlydiesel.com/denni...0/img_3199.jpg
Pioneer 6x8s in Factory Rear Location

https://www.strictlydiesel.com/denni...0/img_3384.jpg
Starting the CLD on the Floor.

https://www.strictlydiesel.com/denni...0/img_3385.jpg
05-07 Dash Center Pieces getting Painted

https://www.strictlydiesel.com/denni...0/img_3386.jpg
Upgrading to 11-16 Center Console too.

https://www.strictlydiesel.com/denni...0/img_3387.jpg
Floor CLD Done!

https://www.strictlydiesel.com/denni...0/img_3399.jpg
Laying out RCA Cables Up the Center of the Floor

https://www.strictlydiesel.com/denni...0/img_3400.jpg
Power, Ground and Turn-On Run Up Floor with 4" Gap. Every component in the system get Power and Ground from the Amp Rack. Key-on for the Head Unit is Amp Rack power switched by a relay. No audio connected component has ANY power or ground from ANY other location.

https://www.strictlydiesel.com/denni...0/img_3426.jpg
Sound Blocking Material Installed on Floor

https://www.strictlydiesel.com/denni...0/img_3545.jpg
Working On Custom Head Unit Mounting Brackets

https://www.strictlydiesel.com/denni...0/img_3548.jpg
Head Unit Solid Mounted (the plastic dash kit sucked)

https://www.strictlydiesel.com/denni...0/img_3563.jpg
Head Unit and Pre-Amp Test Fit

https://www.strictlydiesel.com/denni...0/img_3565.jpg
Head Unit and Pre-Amp Brackets

https://www.strictlydiesel.com/denni...0/img_3594.jpg
Test Fit of Bezel for Relocated AC Controls

https://www.strictlydiesel.com/denni...0/img_3595.jpg
Underdash Aux Fuse Panel for Center Console, Inverter, Upfitter Switches plus Relays for Audio and Alarm Functions (unfortunately, you have to take half the interior apart to change a fuse...oh well).

https://www.strictlydiesel.com/denni...0/img_3596.jpg
Assembled Dash with AC Bezel and Pre-Amp Brackets Powdercoated

https://www.strictlydiesel.com/denni...0/img_3598.jpg
Upfitter Switch Wires Labeled for Future Use (switch 4 controls center console inverter)

Continued in next post...

Continued from Previous Post...

https://www.strictlydiesel.com/denni...0/img_3599.jpg
Designing the Amp Rack

https://www.strictlydiesel.com/denni...0/img_3600.jpg
Amp Rack (v1) After WaterJet and Bending (ended up having to build a v2 with a few minor changes)

https://www.strictlydiesel.com/denni...0/img_3601.jpg
Test Fitting Amp Rack Behind Rear Seat

https://www.strictlydiesel.com/denni...0/img_3791.jpg
First Amplifier Test Fit on Amp Rack

https://www.strictlydiesel.com/denni...0/img_3792.jpg
ALL Wires Pass Through Grommets. All Components Attached with Machine Screws to PEM Threaded Inserts in Amp Rack

https://www.strictlydiesel.com/denni...0/img_3793.jpg
Rivnuts Used to Attach Amp Rack to Truck Body

https://www.strictlydiesel.com/denni...0/img_3796.jpg
2D Side View CAD Design of Sub Enclosure (it was a trick to get the airspace I needed under the seat)

https://www.strictlydiesel.com/denni...0/img_3797.jpg
Once I had the Profile Figured Out, I went to 3D Software to Finish the Design

https://www.strictlydiesel.com/denni...0/img_3798.jpg

https://www.strictlydiesel.com/denni...0/img_3830.jpg
17 Total Pieces for the Sub Enclosure, ALL Cut on a WaterJet Machine (best fitting enclosure I've ever built)

https://www.strictlydiesel.com/denni...0/img_3850.jpg
About 80% Assembled

https://www.strictlydiesel.com/denni...0/img_3983.jpg
Ready for Rhino Liner

https://www.strictlydiesel.com/denni...0/img_3996.jpg
Back from Rhino Liner, Subs Installed

https://www.strictlydiesel.com/denni...0/img_4056.jpg
Baffle Plates Installed (so subs are not firing into carpet)

https://www.strictlydiesel.com/denni...0/img_4058.jpg
Installing Sub Enclosure in Truck

https://www.strictlydiesel.com/denni...0/img_4060.jpg
Sub Enclosure and Seat Installed (with LMI Welding Rear Seat Spacers)

Continued in next post...

Continued from Previous Post...

https://www.strictlydiesel.com/denni...0/img_4070.jpg
Amps Getting New 8ga Power and Ground Cables

https://www.strictlydiesel.com/denni...0/img_4071.jpg
Amps and Other Components Final Mounted on Amp Rack (hung up for easy wiring on both sides)

https://www.strictlydiesel.com/denni...0/img_4100.jpg
Test Fit of Dual Speaker Mount from Custom Speaker Pods

https://www.strictlydiesel.com/denni...0/img_4101.jpg
Fitting the Tweeter in the Door Pod

https://www.strictlydiesel.com/denni...0/img_4108.jpg
Steel Reinforcement Rings with Threaded Inserts for Speaker Pods (so I'm not attaching speakers to plastic)

https://www.strictlydiesel.com/denni...0/img_4109.jpg
Test Fitting Speakers with Reinforcement Rings

https://www.strictlydiesel.com/denni...0/img_4110.jpg
Pods Painted and Reinforcement Rings Attached

https://www.strictlydiesel.com/denni...0/img_4112.jpg
Pods Attached to Door Panel and Speakers Installed (still need to paint the screw heads)

https://www.strictlydiesel.com/denni...0/img_4194.jpg
Amp Rack and Equipment Fully Installed and Wired in the Truck! (this was a LOONNNGGG Time Coming)

https://www.strictlydiesel.com/denni...0/img_4195.jpg
Amp Rack with Seat Installed and Folded Forward

Sorry again for the length of these updates. Been going too many directions and this build took way too long to complete. I started the bulk of this in January of 2021. The truck was down for about 6 months with all of the interior out and everything I did inside, then it was on the road again while I designed and built the sub enclosure and amp rack. I took it down again in December of 2021 to work on mounting the speakers in the doors, battery cables, power and ground for the audio equipment, alternator and lots of other little details...and it just came together this past weekend. At this point, I'm driving and listening and adjusting until I can get with a close friend and spend time with his ears and his analyzer to dial it in. All in all, I'm damn happy with how it came out and how it sounds, and all of the "old school" equipment I wanted to use so badly is working great!