Diesel Bombers

Diesel Bombers (https://www.dieselbombers.com/)
-   24 Valve 2nd Gen Dodge Cummins 98.5-02 (https://www.dieselbombers.com/24-valve-2nd-gen-dodge-cummins-98-5-02/)
-   -   Still won't start (https://www.dieselbombers.com/24-valve-2nd-gen-dodge-cummins-98-5-02/63134-still-wont-start.html)

navy_welder 11-23-2010 07:21 PM

I found one I just don't want to spend 300 on a Ho ECM and it not work and sorry bout earlier had a frustrating day


Any one got one just sitting around

---AutoMerged DoublePost---

I mean if someone has one they are willing to offer up for the experimentation I would be more than willing lol but if so pm me or something

Red_Rattler 11-23-2010 07:35 PM

I still think i have an ecm outa my 2000 non ho though

mishkaya 11-23-2010 07:37 PM

I don't want to insult your intelligence, but when you crank the engine, does the tach move? It's possible the cam position sensor got disconnected when the VP44 was replaced. If it's not working the VP44 will not function. As stated earlier, you might want to check your fuel relay (you can swap it with the horn relay). Also check the wiring connection at the VP44. If all else fails, you can hot wire the VP44 to eliminate that as a possibility of failure. For that you need to run power to the #7 pin and ground the #6 pin; that will run the VP44 independently of the ECM. If the truck starts, you will know that the problem is elsewhere. If it doesn't, it could be injectors, or the fuel pump...

Farmboy 2.0 11-23-2010 07:46 PM

Ok maybe a dumb question but are the injectors seated properly? Connecting tubes not seated properly? Have you cracked an injection line at the head to see if there fuel and the connecting tubes?

navy_welder 11-23-2010 07:50 PM

I know the cs is plugged in cause I went over everything on the harness and I could do that

---AutoMerged DoublePost---

And thank you for the offer on the 00 ECM but that one requires a crank and cam sensor instead of the cs only but I do appreciate it:choochoo:But for future reference it has to be a 01 or 02 manual ECM

crzycummins 11-23-2010 08:14 PM

:humm:

navy_welder 11-23-2010 09:06 PM

Oh and I put a new relay in the truck on the fuel system and also I have a fass platinum 95

---AutoMerged DoublePost---

And the wires on what connector the ip connector or the ECM connector and to make it easier what color are the wires

mishkaya 11-24-2010 05:43 AM


Originally Posted by navy_welder (Post 656543)
Oh and I put a new relay in the truck on the fuel system and also I have a fass platinum 95

---AutoMerged DoublePost---

And the wires on what connector the ip connector or the ECM connector and to make it easier what color are the wires

You need to hot wire the VP44 directly. I cannot recall the colors of the wires going in, but it doesn't matter as the connector shows the pin numbers right on the harness side.

navy_welder 11-24-2010 09:36 AM

Ok will do but it won't be for a ew days I am officially on a liquid diet for the rest of the week haha

---AutoMerged DoublePost---

:jump::tttt::rocking: with plenty of music I think I'm already bout to get the cops called on me haha

mainman300 11-24-2010 11:40 PM

Are ya getting smoke out the exhaust? If so is it white or black?


All times are GMT -5. The time now is 04:39 PM.


© 2024 MH Sub I, LLC dba Internet Brands