Intake Manifold Swap
Can an Intake Manifold from a 94 12 vavle fit a 91.5 12 valve?? The reason I ask is I can't find an aftermarker high performance intake manifold but found an AFE Intake Manifold for a 94 and just wondering if it would fit?? Thanks!
|
I believe it should work but I would spend the money on something else. You can make a lot of power with the factory one
|
Not gona fit without hood triming a stock 3rd gen or cooler tubz flow just as good
|
So a stock 3rd Gen Intake Manifold WILL fit on a 1st gen 12 valve and flow better than the stock 1st Gen Intake Manifold??? Is that what your saying? Swap the 1st Gen with a 3rd Gen?
|
they are saying dont do it. its not worth the money for the power gained unless your way up there on the dyno. there are way better mods!
|
Well I already got a big to do list for it this winter just trying to find an Intake Manifold to help a lil. So far my list includes
HX35 Turbo New Exhaust Manifold 4 inch dual exhaust out the back with 5 inch tips ARP Head Studs 165 GPH Air Dog Fuel/Lift Pump 60 HP Injectors Denny T Fuel Pin Rebuild Trans With Suncoast Torque Converter, BD Valve Body and Deep Oil Pan And A Better Air Intake and Filter And Intake Manifold What Yall Think? :humm: |
if you use a suncoast converter use their VB
put the 3200 gov spring on it a boost fooler for the hx35 head studs at this point arnt necesary but good insurance. could go without with these mods |
Im saying that a 3rd gen and cooler tubz flow better then stock 1st gen plus cooler tubz give you a dropin egt of 50 to 100you degrees and as far as your mods 366 gov spring m&h dynamic timing advance a bigger turbo s300 or hx super 40. And a goerend trans and converter and a dnr customs s&b intake
---AutoMerged DoublePost--- Cooler Tubz Rock - Page 3 - Dodge Cummins Diesel Forum |
...... I'm so confused
OK are there any Intake Manifolds that fit any other Cummins 2nd Gen, 3rd Gen, Etc, Ect, that will fit on a 91.5 Cummins? I found a company that makes some bad hiney ones but don't offer one for the 1st gen just 94 and up like always so jw if any will bolt up???? I dc about "stock flow" or whatever any aftermarket horn HAS to be better than a square stock one and i will be upgrading the boost tubes from turbo to intercooler and intercooler to horn so I want a better horn. if not for performance then for looks cuz it's going to be powder coated blue like the truck. Thanks! ---AutoMerged DoublePost--- The ones I found are Pusher Intakes they have one for the 94 12 valve. Idk why it woulndn't fit? |
Check the link I posted it explain the uses of a 3rd gen and cooler tubz. The grid heater are the same as a 94+ its contact with 1sta gen hoods that's why aftermarket ones don't work the hood hits and if you doing the intercooler charge pipes get a set of cooler tubz. Those pushers are a cheap knock offs
---AutoMerged DoublePost--- http://www.dieseltruckresource.com/d...7&d=1309999193 ---AutoMerged DoublePost--- http://www.dieseltruckresource.com/d...7&d=1309999193 ---AutoMerged DoublePost--- Grids are the same as newer trucks so it'll bolt up. ---AutoMerged DoublePost--- The height and angle of the pipes is what matters |
All times are GMT -5. The time now is 11:27 PM. |
© 2024 MH Sub I, LLC dba Internet Brands