Wont start after spring and fuel system install
Hey guys happy 4th
well I redid my entire fuel system with a draw straw 2,holley black pump to 2 frame mounted filters, all with 1/2" rubber line.did my 3200 spring whole thing went smoothly,removed the power screw top went on no prob.didnt touch the timing.checked solenoid,bled system through injector lines and pump supply line,nothing.when i crank i get it to spin one revolution by itself then thats it..Any help much appreciated :tu: |
When you say it'll "...spin through one revolution then that's it." are you saying it fires for one revolution then dies? Or do you mean it'll spin but doesn't fire and dies? If the former, it's got to be where you've just been. Meaning you're sucking air somewhere, (probably). If the latter, check your battery open voltage, (disconnect it from the truck) all grounds, and your FSS. I know you said you checked it, check it again. You can never be too sure... (Don't ask me how I know...)
|
I mean it actually fires one revolution blows a puff of smoke then thats it.I can keep cranking and it wont do anything after that.I'll try putting more fuel in cause i have a 1/4 tank.cant find a leak I sealed every fitting,could the return line be the culprit it has a small kink. Thanks for the reply
|
Make sure you have 12 volts at the shutdown solenoid after it dies. If so bleed it again. Sometimes air gets trapped and works it's way to the injectors after the system is all apart. From what you describe it sounds air locked but check the voltage first. Good luck:rocking:Rocky
|
well still no luck.Checked the solenoid and 12 v, Bled each line,now shootin straight fuel with no bubbles.Idk what else to do.Thanks for the help guys
|
Check all the lines before your new pump I had a leak that would leak air in but not fuel out and it would make it to where I would bleed the lines and it would run then I would shut it off and the next time I would go to start it I would have to bleed the lines again so if u think it's tight go just a little more good luck I know your:argh:Over it lol
|
you could sell it and get a 2001!! :tu:
|
Originally Posted by SmokiinRam
(Post 770412)
well still no luck.Checked the solenoid and 12 v, Bled each line,now shootin straight fuel with no bubbles.Idk what else to do.Thanks for the help guys
|
Turn the full fuel screw one more full turn and raise the idle screw one full turn or put your foot on the pedal about 1/4 way to floor.
|
I just think i found my problem but im 1000 miles away so i cant test it,But i wired my fuel pump to my cigarette lighter so when Im cranking the pumps not on thus not supplying fuel to push the air out.but when the key is in just the on position it pumps
|
That could do it.
|
ya but if hes getting fuel to the injectors wouldnt it still run until it uses up all the fuel in the lines?
|
Okay well i tried again and this time the pump is on while the engine is cranking,same result.and i also tried wide open and half throttle still nothing.Think Ill tear it all apart again to see if it wont go when i put it back together.If not its getting towed monday.
|
It sounds like you're sucking air. Try pressurizing the fuel tank with a couple pounds of air pressure (put a blow gun in the filler spout with a rag wrapped around it and give it a couple puffs). Have a buddy look for fuel leaks. A leak will be easier to find under pressure. With your pump running and the truck not running does the fuel pump stop or change sounds like it is building pressure? If it keeps running like it has no load on it it is not building up pressure ( leak). It's compression ignition if it has fuel it should start.:rocking:Rocky
|
Well I feel dumb.I played with the throttle index today and she fired right up :argh:..mustve been way off cause i tried it at every pedal position..Thankyou guys for the help:tu:
|
All times are GMT -5. The time now is 05:31 PM. |
© 2024 MH Sub I, LLC dba Internet Brands