Diesel Bombers

Diesel Bombers (https://www.dieselbombers.com/)
-   12 Valve 2nd Gen Dodge Cummins 94-98 (https://www.dieselbombers.com/12-valve-2nd-gen-dodge-cummins-94-98/)
-   -   Additives for blowby? (https://www.dieselbombers.com/12-valve-2nd-gen-dodge-cummins-94-98/49061-additives-blowby.html)

85_305 04-20-2010 06:47 AM

Death85- u don't think running both compounds would be a bad idea? I'm down for trying both as long as you don't see it being bad. I'll run restore first so it can do its thing then a day or 2 later oput in lucas

Tl- I need my truck though so that sort of downtime would kill me. Not to mention that's a LOT of work lol

wes-cummins 04-20-2010 08:23 AM

just run it like it is for now, extend the breather tube back so it aint underneath the cab,
and i wouldnt run more than one or 2 qts of lucas in it

Drothgeb 04-20-2010 08:50 AM

Did this just start, or has it been a gradual thing? Blow-by shouldn't be much of an issue while sitting at the intersection idleing. It's normally more of a high boost/hp issue.

To me, it sounds like you have a broken ring or two. Do a compresssion check!

85_305 04-20-2010 09:28 AM


Originally Posted by wes-cummins (Post 541675)
just run it like it is for now, extend the breather tube back so it aint underneath the cab,
and i wouldnt run more than one or 2 qts of lucas in it

I'll prob use one can of restore and one quart of lucas and call it good between oil changes.


Originally Posted by Drothgeb (Post 541688)
Did this just start, or has it been a gradual thing? Blow-by shouldn't be much of an issue while sitting at the intersection idleing. It's normally more of a high boost/hp issue.

To me, it sounds like you have a broken ring or two. Do a compresssion check!

I bought the truck with this blow-by. It hasn't changed in intensity or smoke since I've owned it.

HAYMAFIA 04-20-2010 10:49 AM

i had one did the same. you could see it when sitting at a red light. one day while pulling a 40' trailer i rapped it up to around 100 mph and it started knocking. with clutch in no knock. i ended up breaking the thrust bearing. i could have done rods and main bearings and had it covered. 290,000 miles or so when it happened. no fuel plate bigger injectors no afc foot. little too "hot" for a work truck but itd pull like hell.

85_305 04-20-2010 10:59 AM

so what was the reason it blew a thrust bearing?

wes-cummins 04-20-2010 12:22 PM

insufficient lubrication and working it to hard, iv seen one go when i was helping a guy work on his pull truck, swapped the crank and and the input shaft was a touch to long,

Death85e 04-20-2010 11:26 PM

I have used both products at the same time for a bandaid to get me by till i could afford a complete rebuild . Just do not go overboard on the lucas if you make the oil to thick with it you will be doing a motor transplant as opposed to a rebuild.

85_305 04-21-2010 07:59 AM

Excellent input so did it work ok using both products? Quell any blowby or anything else? Thanks for the input man

dima4855 08-22-2013 10:11 PM

Does Lucas work
 
So does Lucas work???
I have very minor blow by on 5.9 Cummins, just a little bit of smoke from the oil cap if you look just right and also little bit of smoke from the breather under the engine.


All times are GMT -5. The time now is 06:34 AM.


© 2024 MH Sub I, LLC dba Internet Brands