All Head Light On Mod 01-02 GM pickup
#1
All Head Light On Mod 01-02 GM pickup
This Mod works for All the GM pickups IIRC from the years 00-02. I know for a fact it works on 01-02 but correct me if im wrong.
The mod Allows you to have your Low Beam and High Beam headlights on at the same time only when your high beams are switched on.
Disclaimer: If you live in Texas do this mod at your own risk. It is illegal to have more than 4 lights on at one time
1.First you will need a Screw driver, 1/2 inch socket with ratchet, wire cutters/strippers, Scotchlok, Eye terminal, Zip ties, pliers, and Wire. These parts can be purchased at a local radio shack , auto zone, or wallmart if you don't have them on you.
2. Open up the hood of your Beast.
3. Use the socket wrench to remove the Bracket in the corner that is connected to the firewall and fender that is being held in place by four 1/2 inch bolts.
4. With it removed place it in a convenient place.
5. Next remove the cover for the electrical center.
6. Now look over the electrical center and look at the side facing the engine and you will notice two tabs sticking out...
Push down on the electrical center cover and slide the cover over the tabs that stick out (i used a screw driver). After you done that the Electrical cover should be able to come off by pulling straight up on it
The mod Allows you to have your Low Beam and High Beam headlights on at the same time only when your high beams are switched on.
Disclaimer: If you live in Texas do this mod at your own risk. It is illegal to have more than 4 lights on at one time
1.First you will need a Screw driver, 1/2 inch socket with ratchet, wire cutters/strippers, Scotchlok, Eye terminal, Zip ties, pliers, and Wire. These parts can be purchased at a local radio shack , auto zone, or wallmart if you don't have them on you.
2. Open up the hood of your Beast.
3. Use the socket wrench to remove the Bracket in the corner that is connected to the firewall and fender that is being held in place by four 1/2 inch bolts.
4. With it removed place it in a convenient place.
5. Next remove the cover for the electrical center.
6. Now look over the electrical center and look at the side facing the engine and you will notice two tabs sticking out...
Push down on the electrical center cover and slide the cover over the tabs that stick out (i used a screw driver). After you done that the Electrical cover should be able to come off by pulling straight up on it
Last edited by 2500HeavyDuty; 01-26-2008 at 06:23 PM.
The following users liked this post:
slowtowpig (06-15-2008)
#2
7. Too make things easier now free up the huge bundle of wires that is attached to the fender liner by pulling on it (this may take some persuasion)
8. Next is to Pick up the electrical center and prop it open. There is 3 tabs thats are holding the center to the mount. Bend them back and Pick up the whole center and prop it open exposing the underside of it.
9. Now locate the yellow wire that is in the tan wire block, this is the wire you want to ground for your mod.
10. Use a scotchlok and attach your wire onto it. Double check and make sure it is a a solid connection.
8. Next is to Pick up the electrical center and prop it open. There is 3 tabs thats are holding the center to the mount. Bend them back and Pick up the whole center and prop it open exposing the underside of it.
9. Now locate the yellow wire that is in the tan wire block, this is the wire you want to ground for your mod.
10. Use a scotchlok and attach your wire onto it. Double check and make sure it is a a solid connection.
The following users liked this post:
slowtowpig (06-15-2008)
#3
11. Now Re-assemble everything back together wire sticking out of the bottom of the electrical center. And to make things nice and neat zip tie down the loose wire to the huge bundle of wires that goes into the fire wall.
12. Now to find a ground to connect your wire to. There are many places to connect it to on the firewall
I chose to use an eye terminal and connect it to an existing ground i have made before.
With the yellow wire grounded your headlight mod is complete.
12. Now to find a ground to connect your wire to. There are many places to connect it to on the firewall
I chose to use an eye terminal and connect it to an existing ground i have made before.
With the yellow wire grounded your headlight mod is complete.
Last edited by 2500HeavyDuty; 01-27-2008 at 06:25 AM.
The following users liked this post:
slowtowpig (06-15-2008)
#4
#5
Fixed it.....
Last edited by 2500HeavyDuty; 01-26-2008 at 06:24 PM.
#6
#7
#9
#10