Diesel Bombers SIGN UP NOW

National Association of Diesel Motorsports
Go Back   Diesel Bombers > Dodge Cummins > 5.9 Liter CR Dodge Cummins 03-07
Sign in using an external account
Register Forgot Password?
Search


Registered Members don't see these ads. Register now it's free!

5.9 Liter CR Dodge Cummins 03-07 Discussion of 5.9 Liter Dodge Cummins Diesels with Common Rail Injection

Welcome to Diesel Bombers Forums!
Welcome to DieselBombers .com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Diesel Bombers Forums community today!


My truck seems to run& drive fine. When you free rev it slow up to 3000rpm, it will sound fine, or when you drive it it runs flawlesly lots of power, but if you give it a quick rev up thru the RPMS, it will ... JOIN NOW TO REMOVE TRACER

Reply
 
 
 
submit to reddit
 
LinkBack Thread Tools Search this Thread
  #1  
Old 04-22-2010, 08:23 PM
392hemix's Avatar
Diesel Wrench
Status: driving around

jonny grubisa
   
View Member's Albums

Default 04.5 wont not rev through the rpms smooth?

My truck seems to run& drive fine. When you free rev it slow up to 3000rpm, it will sound fine, or when you drive it it runs flawlesly lots of power, but if you give it a quick rev up thru the RPMS, it will pop, it sounds like the timming is off, or air/water in fuel, that kindof poping noise. why does it do this? is this a common thing? still very much a newbie to the common rails, and the smarty tunner. It doesnt do it as bad on the lower tune or tunes without the timming added. I have it on level 6 currently. Any help or suggestions?

392hemix's Sig:97 Dodge Ex-cab, 4x4, 12 valve, AEM intake, stock HX35 turbo with bd boost elbo, AFC washer flip barrel ground .090, #0 plate full forward, 4K GSK,Mack 2095 rack plug. stock timming@14degrees, 4'' straight exhaust...47re auto, 5qrt ats tranny pan,triple disk Goerends billet torque converter, Goerends high PSI valve body, billit imput shaft,suncoast HD rebuild kit 3:54 gears, 315/75/17 tires 6" lift. trq 728.71 hp312.67
Reply With Quote
  #2  
Old 04-22-2010, 09:07 PM
ArizonaRedneck's Avatar
BOMBARDIER
Status: Stand for what is right, even if you stand alone

   
View Member's Albums View Member's FaceBook Profile

Default

id be curious to what your timing is set at when your smarty is at 6 and what your fuel pressure gauge is at when you are at 3000 rpm's
Reply With Quote
  #3  
Old 04-24-2010, 05:04 PM
392hemix's Avatar
Diesel Wrench
Status: driving around

jonny grubisa
   
View Member's Albums

Default

dont have a fuel psi gauge, and i am thinking maybe the timming is not set correct, or the fuel psi could be an issue, but i have heard that you should be able to make 500hp easy with stock fuel system which im not even close to making. im playing with smary it just seems wierd to me that it runs so good under power but if you just give it a quick rev, like you would to clean it out it will pop bigtime after 2000rpm.
Reply With Quote
  #4  
Old 04-26-2010, 06:28 PM
tdiezel's Avatar
Diesel Enthusiast
Status: Diesel and Beer, Its St. Pattys' everyday!!

   
Default

Your truck will enter free revolution at 3200 RPM's. Is it a popping noise over and over again until the RPM's come back down? If thats the case you don't have enough fuel to support the higher RPM range with the smarty or whatever you have. Do you have a FASS or Airdog system to keep fuel pressure up? If not I will say that is your problem. You can't meet the fuel demands and that causes the popping noise.

tdiezel's Sig:04.5 Dodge Ram 2500 QCSB 6spd
Reply With Quote
  #5  
Old 04-26-2010, 06:38 PM
392hemix's Avatar
Diesel Wrench
Status: driving around

jonny grubisa
   
View Member's Albums

Default

The pops more like after 2000 rpm, it will just go pop, like a back fire and i let out of it, it will not do it if im down shifting and give it a quick rev, just if its at a stand still and you give it a quick blast and after 2000rpm it goes pop, and i dont hold it cause it sounds bad, if i rev it slow up to 3 and hold it, the truck runs fine no pop or back fire.
Reply With Quote
 
 
 
submit to reddit
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search


 
All times are GMT -5. The time now is 11:16 PM.

Copyright And Legal Notice Links Of Interest

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Diesel Bombers ® - All Content Protected Under Intellectual Property Rights Law of Registered Trademarks
Reg. No. 3,494,401 Cls. 100, 101 & 104 Under Int. Cl. 38
USE AT YOUR OWN RISK WE HOLD NO LIABILITY FOR ANY CONTENT RIGHT, WRONG OR INDIFFERENT

Protected by Copyscape Duplicate Content Check