Diesel Bombers - Search Results



Showing results 1 to 25 of 84
Search took 0.00 seconds.
Search: Posts Made By: davidthomas
Forum: 5.9 Liter CR Dodge Cummins 03-07 07-16-2017, 03:46 PM
Replies: 3
Views: 389
Posted By davidthomas
Clean your ground wire thats directly above the...

Clean your ground wire thats directly above the transmission bolted to the underside of the cab, it feeds into those sensors and can really screw things up
Forum: 12 Valve 2nd Gen Dodge Cummins 94-98 07-16-2017, 03:42 PM
Replies: 1
Views: 354
Posted By davidthomas
12 valves can be gutless compared to some of the...

12 valves can be gutless compared to some of the newer motors (460-500 lb ft vs. the new almost or at 900 lb ft.) Theres a million different ways to go with these. Personally in your case I would try...
Forum: 12 Valve 2nd Gen Dodge Cummins 94-98 07-15-2017, 09:27 PM
Replies: 2
Views: 610
Posted By davidthomas
If you have everything apart, take it to a shop...

If you have everything apart, take it to a shop to have it boiled out. They can and should do the head and block with nothing in/on them and that way you get a clean block and can know for sure that...
Forum: 12 Valve 2nd Gen Dodge Cummins 94-98 07-15-2017, 09:02 PM
Replies: 0
Views: 264
Posted By davidthomas
Lots of smoke, cant go above 1300-1500 rpms

I have a 94 that cannot get above 13-1500. Its a new rebuild that just went back in. I went ahead and checked the IP timing and i didnt but it could be pinned now at TDC on both motor and pump....
Forum: 24 Valve 2nd Gen Dodge Cummins 98.5-02 06-14-2017, 12:43 AM
Replies: 7
Views: 434
Posted By davidthomas
If you are in a bind and need to test you can...

If you are in a bind and need to test you can always t into the line and check it with a standard cheap pressure gauge, expect about 15-18ish psi. Now beyond that, I wouldnt do a thing with the fuel...
Forum: 24 Valve 2nd Gen Dodge Cummins 98.5-02 06-14-2017, 12:38 AM
Replies: 8
Views: 435
Posted By davidthomas
You say APPS, I imagine you mean the TPS?? If so...

You say APPS, I imagine you mean the TPS?? If so you did calibrate that with an ohms meter and the two pins off the ecm correct? Second. Check grounds. Make sure everything is getting a good ground,...
Forum: 5.9 Liter CR Dodge Cummins 03-07 06-05-2017, 02:08 AM
Replies: 2
Views: 489
Posted By davidthomas
White smoke is typically just the water vapor(at...

White smoke is typically just the water vapor(at least it is here in montana) , dont worry about injectors until you get a constant haze of smoke coming from your truck at idle and light throttle....
Forum: 5.9 Liter CR Dodge Cummins 03-07 05-30-2017, 12:54 AM
Replies: 2
Views: 376
Posted By davidthomas
I would try to get that on a scan tool, but for...

I would try to get that on a scan tool, but for the time being potentially an issue with FCA??
Forum: 5.9 Liter CR Dodge Cummins 03-07 04-10-2017, 01:47 AM
Replies: 7
Views: 364
Posted By davidthomas
Thats really strange. I wouldn't think the grid...

Thats really strange. I wouldn't think the grid itself is bad. Im not sure if the cmputer would be able to sense that. My guess is it has a feed from feed out of the solenoid into the computer as...
Forum: 5.9 Liter CR Dodge Cummins 03-07 04-06-2017, 11:17 PM
Replies: 2
Views: 342
Posted By davidthomas
Make sure all fuel lines are tight just so you...

Make sure all fuel lines are tight just so you dont suck air and lose the prime back to the tank.
Forum: 5.9 Liter CR Dodge Cummins 03-07 04-06-2017, 11:13 PM
Replies: 7
Views: 364
Posted By davidthomas
2609 is your intake heater, go to the passenger...

2609 is your intake heater, go to the passenger battery and check your heater solenoids. Theres two of them attached to the battery tray kind of on the inside of it. Check the press on wires, very,...
Forum: 5.9 Liter CR Dodge Cummins 03-07 04-06-2017, 01:51 PM
Replies: 7
Views: 540
Posted By davidthomas
Check your apps, etc. The APPS you can turn...

Check your apps, etc.

The APPS you can turn the key to on but don't start, push the accelerator all the down, and slowly let up on it and you will see the CEL flash several times to acknowledge...
Forum: 5.9 Liter CR Dodge Cummins 03-07 04-06-2017, 01:44 PM
Replies: 2
Views: 341
Posted By davidthomas
What lift pump did you put in? is there still the...

What lift pump did you put in? is there still the in-tank pump?
Forum: 5.9 Liter CR Dodge Cummins 03-07 04-06-2017, 01:39 PM
Replies: 7
Views: 364
Posted By davidthomas
p0602? it should have 4 numbers in each, or...

p0602? it should have 4 numbers in each, or p0062, and is this full scan tool or a code reader?
Forum: 5.9 Liter CR Dodge Cummins 03-07 03-06-2017, 10:03 AM
Replies: 13
Views: 833
Posted By davidthomas
Everything instantly starts floating to zero if...

Everything instantly starts floating to zero if not already at it, except volatage, which will also zero, but its moving too rapidly and the weight of the needle is enough with that fast movement to...
Forum: 5.9 Liter CR Dodge Cummins 03-07 02-28-2017, 02:55 AM
Replies: 13
Views: 833
Posted By davidthomas
I went ahead and puled it out, all chips looked...

I went ahead and puled it out, all chips looked good. It seemed as if the needles itself had rotated on then gauge shaft. I reset the cluster and realligned and everything looks good. My one concern...
Forum: 5.9 Liter CR Dodge Cummins 03-07 02-20-2017, 12:18 AM
Replies: 13
Views: 833
Posted By davidthomas
I have for the most part tracked the issue. I got...

I have for the most part tracked the issue. I got it onto a scan tool. It was reading 14.80 as my target voltage and i had just slightly under that as the ecm voltage. Directly off the battery I was...
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-22-2017, 01:26 PM
Replies: 2
Views: 445
Posted By davidthomas
How are you doing this with a common rail? you...

How are you doing this with a common rail? you need the CR injectors on the inside, the old injectors fit into the place of the 02 Injectors? Valve covers lined up? All wiring is able to get to the...
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-22-2017, 01:24 PM
Replies: 2
Views: 445
Posted By davidthomas
Why couldnt you keep the old head? and I havent...

Why couldnt you keep the old head? and I havent heard of people doing this before, I guess it could work but I know for a fact that the feed tubes are different and the thread/size i believe is...
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-19-2017, 11:54 AM
Replies: 6
Views: 495
Posted By davidthomas
aftermarket valve body or a shift kit can prolong...

aftermarket valve body or a shift kit can prolong the life a lot
Forum: 24 Valve 2nd Gen Dodge Cummins 98.5-02 01-18-2017, 08:29 PM
Replies: 5
Views: 473
Posted By davidthomas
For those hp's, non 53 block for everyone, but if...

For those hp's, non 53 block for everyone, but if youre on a budget less build go for the mexico block. It didnt have a casting number and proved to be the strongest of the early 24v's. A vp44 can be...
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-17-2017, 06:33 PM
Replies: 4
Views: 577
Posted By davidthomas
Maybe a loose valve up top slapping, If no miss...

Maybe a loose valve up top slapping, If no miss then a rod shouldnt have been thrown??? I would take a look at that vacuum pump if you can, I know we've got today and tomorrow for a bit of warmth...
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-17-2017, 04:49 PM
Replies: 13
Views: 833
Posted By davidthomas
Update: I put in the new ignition switch. It...

Update:
I put in the new ignition switch. It contacts where its supposed to now but the over charge is still there.
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-17-2017, 04:46 PM
Replies: 4
Views: 577
Posted By davidthomas
Do you notice any difference in power? any...

Do you notice any difference in power? any obvious miss? mileage on the motor? What kind of oil do you run and is it cold where youre at?

Sometimes a loose vacuum line at the pump right there can...
Forum: 5.9 Liter CR Dodge Cummins 03-07 01-17-2017, 12:02 AM
Replies: 13
Views: 833
Posted By davidthomas
Yep, Both batteries are fairly new. One thing I...

Yep, Both batteries are fairly new. One thing I was going to try tomorrow was a replacement of my ignition switch. I checked into the system when I had a short period of time with a genisys and...
Showing results 1 to 25 of 84

 
Forum Jump

All times are GMT -5. The time now is 08:11 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.