2nd Annual Rudy's Diesel Track/Dyno/Sled pull Day
Alright guys, Aaron and I are having his second annual dyno day. The date is set for March 17th 2012. We will be having it at Piedmont Dragway since we were packed at Rudy's shop last year. We will have a mobile dyno come in and are working on a sled pull at night. There will be race classes with BIG payouts, especially for pro street. We will post more info in the next few days, but wanted to get this out there and on people's calendars. Thanks to everyone who came out last year and we look forward to seeing you again this year as we try to grow this event to be similar to TS and Schieds.i'm gonna be handling the sledpull. if you guys plan on pulling please post up what class you would run so i sorta know what to plan a purse for. Test n tune, workstock, 2.6 and Open class just let me know sorta what you have and if you plan on pulling. Me and aaron are trying to make this a great event. thanks yall.
Piedmont Dragway 6750 Holts Store Road Julian, North Carolina 27283 ---AutoMerged DoublePost--- Workstock: The Work Stock (WS) class is designed for daily-driven, on the road pickup trucks (full-bodied diesel pickup trucks). Valid DOT registration and license plates are mandatory. The vehicle may be two or four-wheel drive. Designation: WS followed by competition number Weight breaks: 8500 lbs. Weight is with driver REGULATIONS: Ballast: Ballast is permitted. Hanging front weights are allowed. Ballast may be added in the bed of the truck. If used, ballast must be securely fastened to the bed. Final decisions rest with the NADM Technical Department. Batteries: The batteries must be securely mounted. They may not be located in the driver compartment or forward of the radiator core support. Body: The body must be the OEM truck body, including the full bed floor. The body must retain full sheet metal. Metal after-market hoods are permitted. Fiberglass is prohibited. The hood must be closed and securely latched while the vehicle is hooked to the sled. The complete OEM firewall and OEM floor pan is mandatory. Brakes: Four-wheel hydraulic brakes are mandatory. Chassis: The OEM chassis is mandatory. The engine must be in the OEM location for the body used. The vehicle must retain the full OEM chassis. Wheel tubs, back-half conversions, tube chassis, etc., are prohibited. Cooling System: Radiators must be in the stock location and be of at least stock size. Credentials: All drivers must have a valid state drivers license. Driveline: An OEM transmission and transfer case are mandatory. They must have been an option on a one-ton or smaller pickup. Driver Restraint System: The OEM restraint system is mandatory and must be worn. Engine: The engine is limited to a stock-appearing, OEM make-specific compression ignition engine Exhaust: All vehicles must be equipped to direct exhaust upward. The exhaust must exit rearward of the driver’s compartment. Stacks exiting through the hood or fender well are prohibited. If the muffler or catalytic converter have been changed from stock, Fuel: The fuel must be pump #1/#2 diesel only. Soy/Bio-diesel fuel is permitted. Off-road diesel fuel is prohibited. . NITROUS OXIDE is prohibited along with other oxygen extenders as well as the use of PROPANE is also prohibited. All system components MUST be removed from the truck. Fuel Injection Pump: The fuel injection pump is limited to a stock-appearing, OEM engine model-specific pump only. The use of multiple high-pressure common-rail fuel pumps is prohibited. Powerstroke engines with a single factory turbo may utilize a second HPOP. Pumps from different years in the same engine model may be interchanged. Fuel System: The OEM fuel tank is mandatory and must be used. Racing fuel cells are prohibited and must be removed from the vehicle. Harmonic Balancer: All engines turning 4500 RPM and higher must be equipped with a harmonic balancer or damper meeting SFI Spec 18.1. Hitch: The hitch must be a receiver-style hitch; reinforcements are permitted. Reinforcements must not extend forward of the centerline of the rear axle. Trick hitches are prohibited. The hooking point must be the rear-most point on the vehicle and must be rearward of the stock location of the tailgate. The hitch must be horizontal to the ground and stationary in all directions. Bumpers may be notched or removed. The hitch’s height from the ground may not exceed 26 inches on 4wd units and 30 inches on 2wd units. The hooking point must have a minimum 3.750-inch inside diameter opening for the sled hook. The hooking point will be measured to the center of the clevis loop. Interior: A complete interior, including dashboard, door panels, headliner, etc., is mandatory. Two matching front seats are mandatory. Aftermarket seats are permitted; they must be fully upholstered. All factory controls (lights, signals, horn, windows, wipers, etc.) must be retained and be operative. The use of hand-throttle controls are prohibited. Rear End: Non-OEM rear-end housings are prohibited. It must have been an option on a one-ton or smaller pick up. Rear axle bolts must be covered by a cap or shield. Steering: The vehicle must retain the full, original OEM steering gear. The vehicle must retain the original OEM power steering assistance, if it was so equipped. Additional stabilizers are permitted. Non-OEM power assist methods are prohibited. Street Equipment: Complete headlight and taillight assemblies (all) are mandatory and must be operative. Complete OEM windshield and windows are mandatory. Windows must be operative per factory specifications; that is, they must open and close via OEM electrical or mechanical means. Suspension, Front: The upper mounting point for strut assemblies must be in the factory location. Adjustable caster/camber pillow ball mounts are permitted. The lower control arm may be strengthened provided factory-mounting points to chassis are maintained. The lower mounting point for the strut assembly may be modified for improved caster or camber. Strut tower braces, lower tie bars, sway bars, and limit straps are permitted. Traction bars and devices are permitted. Suspension, Rear: An OEM-style suspension is mandatory. Lowering or raising the vehicle height with suspension modifications is permitted. Traction bars and devices are permitted; they must be bolt-on only; welds are permitted for attachment to frame or axle housing. All OEM suspension mounting points must be retained and used. Sway bars, limit straps, and camber kits are permitted. The rear suspension must maintain a minimum compression shock travel of one inch; compression stops must be adjustable. All rear suspensions must use at least one working shock absorber per wheel. Airbag spring assistance is permitted; airbag compressors must be disconnected. Tires: The tires must be DOT street tires. Cut tires are prohibited. Tow Vehicles: Tow vehicles are prohibited. Transfer Case: Non-OEM transfer cases are prohibited. The transfer case must have been an option on a one-ton or smaller pick up truck. Transmission, Automatic: Non-OEM transmissions are prohibited. Aftermarket torque converters, valve bodies and internal components are permitted. Transmission brakes are prohibited. Any non-OEM floor-mounted automatic transmission shifter must be equipped with a spring-loaded positive reverse lockout device to prevent the shifter from accidentally being put into reverse gear. A functional neutral safety switch is mandatory. All transmission lines must be metallic or high-pressure-type hose. Transmission, Manual: Non-OEM transmissions are prohibited. Aftermarket internal components are permitted. . All manual transmissions must be clutch assisted. Sequential shifters are prohibited. Turbocharger: The turbocharger is limited to a stock-appearing, OEM/Factory make-specific charger only. Turbochargers from different years in the same make may be interchanged. 6.4 liter Powerstroke engines may utilize the factory twin-turbo configuration. Water Injection: Water injection is allowed. the truck. Wheelbase: The vehicle must retain the original factory wheelbase and track width. |
The 2.6 class is designed (full-bodied diesel pickup trucks).
Designations 2.6 followed by competition number Weight breaks 2.6: 8200 lbs. Weight REGULATIONS Ballast: Ballast is permitted. Front hanging weights are allowed, no t to exceed 60 inches forward of the center of the front axle. This will be measured from center of front wheels to end of weight assembly Ballast may be added in the bed of the truck. If used, ballast must be securely fastened to the bed. Body: The body must be the OEM truck body, including the full bed oor. The body must retain full sheet metal, aftermarket hoods are permitted. The hood must be closed and securely latched while the vehicle is hooked to the sled. Brakes: Four-wheel hydraulic brakes are mandatory. Chassis: The OEM chassis is mandatory. The engine must be in the OEM location for the body used. The vehicle must retain the full OEM chassis. Wheel tubs, back-half conversions, tube chassis, etc., are prohibited. Cooling System: Radiators must be in the stock location and be of at least stock size. Credentials: All drivers must have a valid state driver’s license. Driveline: An OEM transmission and transfer case are mandatory. They must have been an option on a one-ton Or smaller pickup. Driveshaft Loops: All trucks must have at least six inch wide u-joint shields around the rear u-joint constructed of at least 1/4 inch steel or 3/8 inch aluminum that will safely contain the u-joint and the end of the rear shaft. All shields must be securely mounted to the vehicle. Any front shaft u-joint that is visible from the side of the truck must be shielded to contain the u-joint and the end of the shaft. Driver Restraint System: The OEM restraint system is mandatory and must be worn. Engine: The engine is limited to a stock-appearing, Engine and transmissions can be interchanged between Dodge, Ford and GM as long as they came in a 1 ton truck or less from the factory. Complete engine must have stock appearance except where otherwise noted in these rules. aftermarket intake manifolds are allowed Exhaust: All vehicles must be equipped to direct exhaust upward. Firewall: The complete OEM rewall is mandatory. Floor: The complete OEM oor pan is mandatory. Fuel: The fuel must be pump #1/#2 diesel, Soy/Biodiesel fuel. Fuel Injection Pump: The fuel injection pump is limited to a stock-appearing, OEM engine model-specic pump only. The use of multiple high-pressure common-rail fuel pumps is legal. Powerstroke engines with a single factory turbo may utilize a second HPOP. Pumps from dierent years in the same engine model may be interchanged. Fuel System: Racing fuel cells are permitted Hitch: The hitch must be a "Reese"-style hitch; reinforcements are permitted. Trick hitches are prohibited. The hooking point must be the rear-most point on the vehicle and must be rearward of the stock location of the tailgate. The hitch must be horizontal to the ground and stationary in all directions. Bumpers may be notched or removed. The hitch's height from the ground may not exceed 26 inches. The hooking point must have a minimum 3.00 inch wide x 3 ¾ length inside diameter opening for the sled hook. The hooking point must be a minimum of 44” from the center of the rear axle to the center of the hooking point. The hooking point will be measured to the center of the clevis loop. Nitrous Oxide: Nitrous oxide is prohibited. No other oxygen extenders are allowed. All system components must be removed from the truck. Propane: Propane is prohibited. All system components must be removed from the truck. Rear End: Non-OEM rear-end housings are prohibited. It must have been an option on a one-ton or smaller pick up. Rear axle bolts must be covered by a cap or shield. Steering: The vehicle must retain the full, original OEM steering gear. The vehicle must retain the original OEM power assistance, if it was so equipped. Additional stabilizers are permitted. Non-OEM power assist methods are prohibited. Suspension, Front: The upper mounting point for strut assemblies must be in the factory location. Adjustable caster/camber pillow ball mounts are permitted. The lower control arm may be strengthened provided factory-mounting points to chassis are maintained. The lower mounting point for the strut assembly may be modied for improved caster or camber. Strut tower braces, lower tie bars, sway bars, and limit straps are permitted. Traction bars and devices are permitted. Suspension, Rear: An OEM-style suspension is mandatory. Lowering or raising the vehicle height with suspension modications is permitted. Traction bars and devices are permitted; they must be bolt-on only; welds are permitted for attachment to frame or axle housing. All OEM suspension mounting points must be retained and used. Sway bars, limit straps, and camber kits are permitted. All rear suspensions must use at least one working shock absorber per wheel. Airbag spring assistance is permitted; airbag compressors must be disconnected. Blocked suspension is permitted. Tires: The tires must be DOT street tires. Cut tires are prohibited. Transfer Case: Non-OEM transfer cases are prohibited. The transfer case must have been an option on a one-ton or smaller pick up truck. Transmission, Automatic: Non-OEM transmissions are prohibited. Aftermarket torque converters, valve bodies and internal components are permitted. Transmission brakes are prohibited. Any non-OEM oor-mounted automatic transmission shifter must be equipped with a spring-loaded positive reverse lockout device to prevent the shifter from accidentally being put into reverse gear. A functional neutral safety switch is mandatory. All transmission lines must be metallic or highpressure- type hose. Transmission, Manual: Non-OEM transmissions are prohibited. Aftermarket internal components are permitted Turbocharger: The vehicle is limited to a 2.6 inducer bore single turbocharger. The compressor wheel must protrude into a 2.6” bore for 1/8”. The inlet will be measured using a 2.65 inch plug the plug must not be able to enter the inducer bore. A stock map width enhancement (MWE) groove is allowed. No MWE groove will be allowed that has a width greater than .200”. All provisions allowing air into the wheel other than via the bore and the MWE groove are prohibited. The vehicle driver will be responsible for making compressor wheel accessible for tech personal to measure bore and be able to inspect compressor wheel. Water Injection: Water injection is Allowed Ice Water Intercoolers Are allowed Wheelbase: The vehicle must retain the original factory wheelbase and track width. Pull track managers (Doug Woodward/ Joe Hakman) will have nal say if a truck is in question Safety will not be sacriced by an unsafe vehicle or driver OPEN CLASS Run wat you brung!!!!!!!!!! nos allowed **i cut a few things out that i know some of you will not have. if you have any ?'s pleae post up. |
Bump it up. only a few weeks away!!!!!!!!!
|
Before....
http://sphotos.xx.fbcdn.net/hphotos-...09119456_n.jpg After... http://sphotos.xx.fbcdn.net/hphotos-...44121376_n.jpg got alot of rocks up. will finish prepping track the day b4 or the day of the pull. |
All times are GMT -5. The time now is 01:59 AM. |
© 2024 MH Sub I, LLC dba Internet Brands