my first 12v conversion
 

I am doing my first diesel conversion. It will be going in a 86 burb.. 93 12v.. wise me luck

need help??? got questions ??good luck, :pca1::pca1:

be sure to start up a build thread and keep us all updated! :pca1: good luck dude!!! :tu:

WISH... me luck not wise me luck lol:tu:.. thanks guys i will...

---AutoMerged DoublePost---

Pulling the motor out of the burb today.. then taken everything off the front of the frame to box it in....

Got some done today got gas tank out and front plow mount off... I can tell this burb was a plow truck.. lots of cutting wheels being used...

got a few pics

Going good cant wait to get that 5.9 down in the burb..:jump::jump::jump:

I need some help?????????? I have a divorced transfer case in my burb. it has the small yoke.. but the trans on the cummins as the big yoke can i buy a big one to go on my tranfer case????? Do they make a slip yoke that fits the trans that is small to match the transfer case:argh::argh::argh:

Have fun man! Its not too bad with these 12v's

And sorry I'm not an expert in that 4wd/Tcase stuff

Im no expert eather but i believe they stopped that in the late 60's. most auto companies didnt make there own 4x4's then. like dana would just ad a transfer case and a frontend. I also believe you can take off that front piece on the case and locate an adapter and sleave and bolt it to your 518a. now that beeing said, that is an 86 and you do have a 518a trany 4x4 in cummins. I took the input shaft out and swaped it into the chevy 205 case and the out put YOLK INTERCHANGES ALSO. I couldnt find a larger yolk eather so if you do let me know. some of those divorced t-cases were dana 30 (i think) (30 or 35) if so im not sure those are interchangable. sorry about the jiberish Shane :humm:

Got motor mounts cut down ready to go....:jump:

no my trany is a 518 2wd going to my divorced tranfercase uses a short drive shaft

You should be able to have a driveshaft shop make you a custom unit. Or they might be able to suggest where to find a large yoke. You can also check the internet for shops that specialize in rock crawlers. They usually have a good line on custom yokes and such.

Well I kinda fixed my trans prob.. got me. Free eaton fuller 10 speed and a sae 2... so I will put it in for the fun of it:yeah:

Can someone tell me a good place to find another sae# 2

Been getting lots done i need to post some pics for you guys

These are just the pics i took the day i took it out of the dodge. I just set it on the chevy frame to move it all to the shop...The miller sticker is some free stuff i get from running a bar

:jump::hellox::yeah:

Got a lot done still have not made my mind up on a trans... Anyone have any input??:humm:

Standard or auto?

If standard, do an NV4500, it'll bolt right up you'll just have to get the driveshaft stuff done.
Auto...... maybe a 47RH or comparable Dodge tranny? Not sure on that one.

This truck here is whats keeping me from getting my burd done

Got new door,fenders,bumper,hood,inner fenders,and flat bed..

Your divorced transfercase is it a np205 if so u can get the 1410 yoke for the front shaft it's the same as the rear on a np205 that's what I did. on a divorce np205 the input and out put shafts are both 31 spline if u look on my build under cummins 5.9 in a blazer u will see a pic I will get u the part number tomorrow it's made by spicer:tu:

---AutoMerged DoublePost---

I found that part number spicer part number is 300483 hope this helps u find what u want

thank you that will help a lot.. i will check yours out

Been working on getting the radiator and inner cooler done today..

Trying to make my mind up

I dont like the way it looks :dang::argh:

I am not happy with it.. but.. i am just going to go with it or i will never get this truck done.. I still have some more stuff to do to it but its 90% done..

I don't think anyone cares about. My post.... lol

I feel the same way when it comes to mine lol but I got a question for u what are u doing with your ac?

I am not hooking it up.. This is just a play truck or I would...

Got the H/D seats in today :jump::jump:

Likin the progress! :tu:

Not getting much done .... Got gout in my foot hope to get back at it this week

Oh that stuff aint fun

NO its not.. But i did get the 3500 painted to day thur all the pain..:s: