New to d max need some help.
I just bought an 02 duramax and have been going over this thing with a fine tooth comb after having my beloved cummins totalled by a dumb 17yr old kid hitting me . So I came across this chevy and I've always been a chevy guy and the price was unbelievable. I changed the fuel filter and everything was good the whole day. I got up to head to work and she fired up and about 5 sec later it died and would not restart. I tried priming the pump and even put all new seals in it and it still I cannot get the primer to get hard. I finally got the truck to start Withe starting fluid which I know is not good buuuuuttt it rules out some things and gets you going in a pinch. So far today it's been starting. I have noticed that my rail press won't get over 15k and it gets up that high as I'm letting off the throttle. What I'm wondering is how to decifer if it's the relief valve, cp3 or filter head. I have no signs of injectors being at fault, truck runs great and has always fired up strongly. It even fired up strong this morning and just died like the fuel was shut off.
|
Sounds like you need to do the bottle/return rate test. Injectors that run fine may still have a high return rate and make it hard for the cp3 to keep up. This is especially apparent while cranking as the cp3 is engine driven and when rpms are low so is output. This also brings up the batteries. Does your engine crank over quickly?
While the true return rate test on the LB7 is difficult as the injectors are under the valve covers, one can relitively easily test the banks of injectors on eash side The pressure relief valve on the LB7 rarely has issues, so I would look at the cp33 and injectors Have you verified the filter head is not leaking air by using a clear hose on the output? |
Originally Posted by 2004LB7
(Post 1103055)
Sounds like you need to do the bottle/return rate test. Injectors that run fine may still have a high return rate and make it hard for the cp3 to keep up. This is especially apparent while cranking as the cp3 is engine driven and when rpms are low so is output. This also brings up the batteries. Does your engine crank over quickly?
While the true return rate test on the LB7 is difficult as the injectors are under the valve covers, one can relitively easily test the banks of injectors on eash side The pressure relief valve on the LB7 rarely has issues, so I would look at the cp33 and injectors Have you verified the filter head is not leaking air by using a clear hose on the output? |
Only thing I'm concerned about is, it looks like previous owner glued the heater plug wire on top of the filter housing and the fuse was pulled. I'll still grab some clear line and see what it's doing. I'd like to just get rid of the filter head amd put a lift pump on it.
|
Also I pulled the intake heater and drilled and tapped it for my boost gauge, how can I get it to not set the engine light ?
|
The only way i know of is turning off the codes with Efi Live
I imagine that you can rig up a resistor in place of the grid heater but dont know how much higher then the resistance of the stock element you can go before the light comes on. If you have to use a low ohm resistor then your better off with efi live as the heat build up will require a really large resistor |
Nu2cummins , you get it to hold prime yet?
|
Originally Posted by thunderhead
(Post 1104285)
Nu2cummins , you get it to hold prime yet?
|
Nu2cummins, Try to plug the return line on pump and see if the primer gets hard .
6 and 8 are high but you should still get a hard prime at least for a while. I just found my problem . Mine would prime but lose it in about 30 seconds then stall . I don't have a scanner yet that will do the test for me . Here is what i did so far. Changed fuel filter and head , changed fuel pressure regulator and fuel pressure valve . Still wouldn't hold prime . Put dye in fuel and found one return leak on injector fixed that. I blocked off fuel going to engine on fuel filter head and primed and it held pressure. So that told me that was good. next i took off fuel pressure line from pump and pumped up primer and it held so that tells me the injectors was not causing the prime lose. So i unplugged the return on the pump and when i pumped it up fuel shot out of there. that line returns straight to the tank . So my check valve in pump is bad. Its leaking and causing it to lose prime. So i took it out and ordering a new pump Monday. Mine started out like yours did lose of power when you get on it then it died and wouldn't start . Some one put a lift pump on it and that's what kept it going for a while until the pump finely gave up. Not sure if that's your prob but i would check. |
One other thing , do you have a lift pump on yours ?
|
All times are GMT -5. The time now is 09:39 PM. |
© 2024 MH Sub I, LLC dba Internet Brands