Diesel Bombers

Diesel Bombers (https://www.dieselbombers.com/)
-   Chevrolet / GMC Diesel Tech Articles (https://www.dieselbombers.com/chevrolet-gmc-diesel-tech-articles/)
-   -   how to make glow plug switch manual operated * (https://www.dieselbombers.com/chevrolet-gmc-diesel-tech-articles/67505-how-make-glow-plug-switch-manual-operated.html)

ruffneck6969 01-13-2011 08:44 PM

how to make glow plug switch manual operated *
 
:argh:my glow plugs will only come on if my motor is all the way cold so how can i put a push button in it so i can control it.........the truck is a 93 gmc 2500 6.5 td HELLLLLLLP NEED TO BYPASS THIS

Crazy 01-13-2011 09:00 PM

10 Attachment(s)
This is a guide to help you install a switch for you to have the ability of extending the glow time. This is helpful when you live in older climates or if you have AC Delco 60g glow plugs. I only suggest installing this if you have self regulating glow plugs. This is a fairly simple modification and if you set everything up yourself you will save quite a bit of money. Most kits for this will cost you over $100, but if you follow this guide you can do it for under $40.

Parts:

* Ford Starter Solenoid [$12 - Advance Auto - 5470277 (S58Z) ]
* #6 or 8 Gauge Wire and Connectors [$14 - Tractor Supply Co. (6 gauge, 2x 24" wires) ]
* Momentary Push Button Switch [$5 - Tractor Supply Co.]
* Switch Wiring and Connectors [In garage]
* Add a Wire Fuse Tap [$7 - Advance Auto - 5080114 (BP/HHH) ]

Total Price for Me: $38
Estimated Time: 1hr 30 mins
Difficulty: Easy

Step 1:
Disconnect battery grounds and then take off the nuts that hold the power lugs on the glow plug relay.

Step 2:
Mount the solenoid in your place of interest (I mounted mine where the Baro sensor was located and relocated my baro sensor).
Hook up switch wire to the "S" lug and feed wire through firewall, make sure you have enough wire to go to switch. Below is where I mounted mine:

Step 3a:
Remove your dash bezel. You can do this by pulling out your cup holder a little bit, dropping your steering column all the way down, and for automatics putting shifter into "1". After that pull the corners and along the top on the bezel. Only thing holding it on are the clips.
After the bezel is loose, pull it away from the dash enough so you can unplug the headlight switch and cargo lamp, and 4x4 switches.
Note: You do not need to remove your bezel if you place switch on one of the two extra switch panels, just pry those out and you can feed wire through.


Drill where you are going to mount your switch and mount it (you have one shot). The next thing you will need to do is run the power to the switch. Using the fuse tap, tap into a fuse that is only has power when key is on and run that wire to the switch (I used Cruise fuse).
After the switch is all hooked up (solenoid and power) go ahead and hook up everything behind the bezel (headlight,cargo, 4x4 switches) and mount the bezel back on the dash.


Step 4:
After everything is done inside the cab, go back and connect the the Solenoid to the Glow Plug Relay. Do this by using the #6 gauge wire and connectors for the lugs. It shouldn't matter how it is hooked up as long as you have one lead on solenoid and one lead on relay, and the other wire on the opposite side of the relay and solenoid. See pictures:
Note: Do not over tighten the nuts on glow relay. New glow relay is $42.


Step 5:
Make sure all the connections on the relay and solenoids are tight and no bare wires are touching that shouldn't be. Hook the batteries back up and test. Turn on key, wait for the glow light to go off and push the new glow button. If working properly the glows will work (hear the click) and the WTS light on dash will light up (97+ WTS light will not light up, the light is computer controlled). If this happens then you are done .

Note: On 97+ trucks you may want to install an extra indicator light to make sure your glows are working.

Crazy 01-13-2011 09:20 PM

did you check see if the wire coming from the battery had power and did you check fuses

---AutoMerged DoublePost---

are you getting any codes

ruffneck6969 01-14-2011 11:54 AM

ya no codes an my fuses inside the truck are all good just does it when the truck is warm or kinda warm the weather here is a high of 10 deg.....just tired of waiting for the truck to cool all the way dwn to start it by glow plugs

---AutoMerged DoublePost---

:jump::jump:thank you for the info once again iam converting it over today cant wait to have it manual opperated

ruffneck6969 01-14-2011 03:08 PM

thanks for the great tips hooked it up runs awsome an glow plugs are nw in my control thank you crazy


All times are GMT -5. The time now is 06:47 PM.


© 2024 MH Sub I, LLC dba Internet Brands