Chevy/GMC Duramax 07.5 -10 LMM Discussion of Chevy and GMC Trucks with LMM Duramax Turbo Diesel Engines

Truck stalling on cold start

Thread Tools
 
Search this Thread
 
  #1  
Old 01-07-2015, 05:13 PM
Mike0885's Avatar
Newbie
Thread Starter
Join Date: Jan 2015
Posts: 4
Likes: 0
Received 2 Likes on 2 Posts
Default Truck stalling on cold start

My truck stalls after one minute of idle, but only the first time I start it. When it's cold outside, it cranks a little for starting and makes a big white cloud. It makes a knocking sound when I run it cold on low rpm.

I just changed all injectors because I had water in fuel. I discovered the problem after having change it all, I had to replace 3 other ones again so I knew that was the problem. So water went in the other 5 new but did not break it, maybe until now? The injector balance were inside the spec when engine was hot.

I thought it was fuel pump that was not delivering enough fuel volume on start but I have no other symptoms related to fuel pump.

Can I drive it like that until something break? I have no engine light or Trouble code and when I run it hit everything's good.

GMC Sierra 3500 2009 SLE duramax lmm
 
The following users liked this post:
geatgavi (02-13-2015)
  #2  
Old 02-13-2015, 01:50 AM
2004LB7's Avatar
Diesel Bomber
Join Date: Dec 2010
Location: Fool's Golden State
Posts: 1,190
Likes: 0
Received 113 Likes on 109 Posts
Default

I would suspect a stuck or leaking injector that clears up when warm. This will be hard on the pistons and cylider walls. Try pulling the glow plugs and disabling the injectors. Crank the engine over and see if you get fuel comming out of any glow plug holes, that will be the bad injector.
 
The following users liked this post:
geatgavi (02-13-2015)
  #3  
Old 05-27-2015, 11:48 AM
AKammo's Avatar
Newbie
Join Date: Aug 2014
Posts: 3
Received 0 Likes on 0 Posts
Default

My 07 LMM just started doing the same thing; stalls after less than one minute of idle, but only the first time I start it in the morning. Check engine light comes on but when I run the codes there are none. I clear it anyway, the check engine light goes out and I crank it again. It cranks over quite a bit before firing but once it starts everything seems fine. Later in the day when I start the truck it cranks over a bit more than usual but starts and runs fine.

Any ideas?
Thanks
 
  #4  
Old 05-27-2015, 12:07 PM
2004LB7's Avatar
Diesel Bomber
Join Date: Dec 2010
Location: Fool's Golden State
Posts: 1,190
Likes: 0
Received 113 Likes on 109 Posts
Default

sounds like an air leak at the filter/housing. try priming it prior to starting and see if it helps. also you can change out the rubber hose coming out of the filter with a clear one and watch for air bubbles. there should be none. if you have air then you may need to rebuild the filter housing. you can find DIY kits for cheap.
 
The following users liked this post:
AKammo (05-27-2015)
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
doublehbar
24 Valve 2nd Gen Dodge Cummins 98.5-02
13
08-09-2015 12:35 AM
dfish001
5.9 Liter CR Dodge Cummins 03-07
7
03-30-2015 03:07 PM
ronstop
5.9 Liter CR Dodge Cummins 03-07
0
02-26-2015 09:48 AM
el_gringoo
Ford Powerstroke 03-07 6.0L
4
12-14-2014 11:03 PM
custom7.3
Ford 83-94 6.9 and 7.3L General
1
11-23-2014 10:44 PM



Quick Reply: Truck stalling on cold start



All times are GMT -5. The time now is 04:55 AM.