The new TNT non race tune keeps throwing p0123?? can't remember for sure right now but it is an overboost code and bob told me to get a boost fooler for that but today it threw p0148... High Pressure Common rail ????

Hopefully Bob and Marco can fix this... Do you fellaz think I should pull the TNT off???

Shane

---AutoMerged DoublePost---

Ok I just talked to Bob and Marco thinks I have a rail sensor issue?? Any one have troubles with these?? I had the commader and it had a wire tap on there... Could this be the problem???

Luvnacummins's Sig:

MPI Twins By Nathan Wright, Ultimate Tranny By OPIE
Stage II CP3,5" exhaust, 9 guages, Srt-10 Hood, on 35" Toyos and 20" rockstars

It may have severed enough wires to where it's causing enough of a voltage drop, setting a code.

RAM CR 24V's Sig:

06 Ram Cummins

Big Sky Bombers Social Group

DIESEL BOMBERS SUPER MODERATOR

CLICK HERE FOR SPONSORSHIP INFORMATION
CLICK HERE TO BECOME A PREMIUM MEMBER AKA BOMBARDIER

Yeah I am headed out to inspect right now...

Hopefully you handle this better then you did w/ the stickers Shane... he he j/k

I hate wire taps for this reason. I'm not sure it's your problem but it's a good place to start. There have been a couple of guys that have had to replace their rail sensors so it isn't uncommon for that either. Sounds like a coincidence though that the rail sensor and the boost code show up with the new tune but Bob and Marco know better than me.

staarma's Sig:

2004.5 2500 White SLT QCSB 4X4 6SPD 3.73 Edge Hot J/A w/ EZ, Smarty Jr. POD, 5" exhaust w/6" tip, AFE Megacannon Stg 2, HTT 62/71/13ss, ATS In/Ex manifolds, Di Pricol rail pressure, Diesel Dynamics Big Line Kit, FASS HPFP, Di Pricol boost and FP gauges w/ Geno's filter lid, CON Fe, Joe Hellman IC, condenser guard, Fumoto valve, PAC Brake, TDK front bumper

Ok so the wire is frayed but not split or broken... I can see bare wire but that is it so I am thinking it's the rail sensor.... Anyone have a part number??? I am goona get one and see what that does....

The part number I believe is 3974092 for the rail pressure sensor. You may want to try Cummins instead of the dealer. I heard there was a huge price difference between the two. Also, Quad has a new harness available so you don't have to wire tap.

I called the dealer today and they said $700 But I have talked to a couple of members and we're thinking it could be the stock fuel system not being able to keep up with the Stage II cp3??? Maybe a possibility... I will try cummins and the dealer's number wasn't that same number so I will call and ask...

Thanks man!!!

Yeah, try Cummins as I think they were around $180. I didn't realize you didn't have a Walbro or the like. Sounds like more money to spend. On second thought, I suppose that if you were constantly draining the rail it could be causing your problems. Basically the ECM tells the FCA what kind of demand pressure it needs then it checks the pressure delta between that and the rail sensor for actual pressure and if the two aren't within whatever spec they determine in the firmware then the check engine light is thrown and it will set a code. This may or may not be the case with your truck. Either way you definately need a new supply side pump with at least 30 PSI available to that modded CP3 I would think.

Yeah I have an airdog that we are going to install within the next week or so... So... Today I go out start the truck and nothing.. No codes none at all today... Romped on it a couple of times and nada??? Im cornfused.... Hopefully though the air dog will be the fix!!!