Hey all,

i am getting a new fuel pump soon and i was wondering if this gauge will work for the first gens, and if anybody has this gauge any input would be great.
http://www.genosgarage.com/prodinfo.asp?number=AM-4360 UL

thanks all.

---AutoMerged DoublePost---

sorry about that the guage didn't come up so go to guages, autometer, and it's the ultralite electric fuel psi guage 30 psi.

DieselPerformanceGuy's Sig:

1992 dodge CTD,auto,RCLB, w250, 170,500 on the odometer,5x.014's , 366 spring, pump maxed,starwheel bottomed , bully dog fuel pin, bully dog 4 inch exhaust, asa modifieds intake,auto meter boost and pyro gauges,isspro 4k tach,ATS 3 peice manifold,3'' homemade coolertubz,and a new 62/65/12 s300 turbo,: next to have,AirDog II 165 fuel pump.
http://s804.photobucket.com/albums/y.../Truck%20pics/

Try this link. Is this the one?

http://www.genosgarage.com/prodinfo....r=AM-4360%20UL



.

Richie O's Sig:

89 Dodge W250, auto, 3.07 factory l/s, 4 inch stans exhaust, S300G 57/64/14, powerstroke intercooler 297 HP. 93 W250 extended cab, rag, 4.10 l/s , 6x16's, 60mm GDS H1C with 16 cm exhaust, work in progress.301 HP

yep thats the one i was asking about, do you know if it will be a direct fit if it even works.

Yes, it should work, with the right install hardware, which I think you need to purchase aside from the gauge. Just a thought, here. Go to the sticky and open the fuel gauge install thread and check out that set up. It litteraly took me 20 minutes to install and that whole kit is almost half the price of the gauge you're looking at.

muskrat's Sig:

93 Dodge W250 CTD
Auto Tranny
Tweeked IP
366 Spring
M&H M4 Fuel Pin
H1C/60mm Wheel/14cm Exhaust Housing
4" Exhaust Out 5" Stack

Not sure on this specific gauge , but I ordered a isspro from genos and the kit came with everyting needed. Mine is mec. but came with the isolator and all the tubing. I would call for sure before ordering. I have had good service from geno's, e gauges.com, and also bought from isspro direct. I have autometers in the 89 ( pryo and boost ). Happy with those also.

alright thanks guys!

---AutoMerged DoublePost---

richie o
is this the same gauge as urs just white, and did ur kit have all the same lines and regulator.

Fuel preasure guage install

Looks the same. Now that I think about it, mine did not come with the rubber line. I just used a piece of rubber marine fuel line to go from banjo to isolator. I also plummed in a snubber incase I had gauge flutter. I do not have flutter so the snubber is wide open.

in genos the exact gauge ur talking about says it has an isolator and 8ft of rubber fuel line.

It says 8 ft of tubing. Thats the little plastic line that goes from isolator to gauge.

http://www.genosgarage.com/prodinfo....ber=ISS-R5604R



.

o so i would have to buy the fuel line and that fitting, am i missing anything else.

---AutoMerged DoublePost---

so then will this kit work.
http://www.genosgarage.com/prodinfo....mber=VULCAN-FH

To be honest, I don't remember. I know I went to the harware store to get the snubber and a couple of barbed fittings. I had the fuel line.

alright i guess i'll get the one from vulcan cuz it comes with the fuel line and boost line and the guage is cheaper especialy without that fuel hose kit.