12 Valve 2nd Gen Dodge Cummins 94-98 Discussion of 12 Valve 5.9 Liter Dodge Cummins Diesels with P7100 Injection Pumps

front driveshaft

Thread Tools
 
Search this Thread
 
  #1  
Old 10-30-2010, 02:19 PM
cummins95's Avatar
Diesel Wrench
Thread Starter
Join Date: Apr 2009
Location: Sullivan County, PA
Posts: 772
Received 48 Likes on 25 Posts
Default front driveshaft

anybody know the difference in lengths front manual to auto? i swapped an nv4500 into my truck n haven't gotten a front driveshaft for it. went out cruisin last night n almost couldnt pull out a stuck 2wd s10 time to cut mine down....
 
  #2  
Old 10-30-2010, 05:45 PM
fivepointohno's Avatar
Diesel Fan
Join Date: Oct 2010
Location: central texas
Posts: 85
Likes: 0
Received 6 Likes on 6 Posts
Default

I think is 3in total 1 1/2 shorter for the front and 1 1/2 longer for the rear
 
  #3  
Old 10-30-2010, 06:02 PM
cummins95's Avatar
Diesel Wrench
Thread Starter
Join Date: Apr 2009
Location: Sullivan County, PA
Posts: 772
Received 48 Likes on 25 Posts
Default

got ahold of my buddy that has one n i measured it, i came up with 5 1/2 inches of difference. got er cut down n welded up, gonna put it in n give it a try. worst case scenario i end up buyin a driveshaft
 
  #4  
Old 10-31-2010, 06:02 AM
fivepointohno's Avatar
Diesel Fan
Join Date: Oct 2010
Location: central texas
Posts: 85
Likes: 0
Received 6 Likes on 6 Posts
Default

damn sorry about that i was way off
 
  #5  
Old 10-31-2010, 08:40 AM
cummins95's Avatar
Diesel Wrench
Thread Starter
Join Date: Apr 2009
Location: Sullivan County, PA
Posts: 772
Received 48 Likes on 25 Posts
Default

haha no problem. i put it in last night, it aint pretty but it'll get me thru for right now. im gonna have to buy one anyway, it kinda spins in an oval now

i managed to burn all the hair off my arm when we were buildin it, i failed to see the 50 feet of waterproof fuse hangin off the bench in front of where i was grindin. all i saw was 2 foot flames on the bench so i grabbed it n threw it on the garage floor, so my right arm is bald now haha

---AutoMerged DoublePost---

yesterday while we were in the process of fixin my truck n tryin to burn down the garage, my friend pointed out that my front axel is not centered, it sticks out further on the drivers side, im assuming this is from the 2.5" lift + the stock track bar. i was lookin at the adjustable one from thuren fabrication, can anybody give me any insight on these? price aint too bad, just wonderin if its gonna last
 

Last edited by cummins95; 10-31-2010 at 08:40 AM. Reason: Automerged Doublepost
  #6  
Old 10-31-2010, 11:07 AM
dan33klein's Avatar
Diesel Bomber
iTrader: (-1)
Join Date: Nov 2008
Location: cherry,il
Posts: 1,019
Received 11 Likes on 11 Posts
Default

look at a dt profab trackbar
 
  #7  
Old 10-31-2010, 05:46 PM
Dirt_Diver's Avatar
Diesel Enthusiast
Join Date: Sep 2010
Location: Funny farm
Posts: 260
Received 5 Likes on 5 Posts
Default

When i swapped the nv4500 in mine i actually used the front driveshaft off of the donor truck which was the dually 5speed but then again too i also used the transfercase but there should be no difference bc their both the same tranfercases except one has a pto in it.
 
  #8  
Old 10-31-2010, 07:19 PM
cummins95's Avatar
Diesel Wrench
Thread Starter
Join Date: Apr 2009
Location: Sullivan County, PA
Posts: 772
Received 48 Likes on 25 Posts
Default

the front driveshaft was the only thing i didnt get with my donor truck. i put the welds to the test today n they held, just wont be able to run 4x4 down the road.
 
  #9  
Old 11-01-2010, 06:31 AM
Heavy Smoker's Avatar
Diesel Fan
Join Date: Sep 2010
Location: Lockport NY
Posts: 67
Likes: 0
Received 1 Like on 1 Post
Default

It problably makes your whole truck shake now.
 
  #10  
Old 11-01-2010, 05:49 PM
cummins95's Avatar
Diesel Wrench
Thread Starter
Join Date: Apr 2009
Location: Sullivan County, PA
Posts: 772
Received 48 Likes on 25 Posts
Default

im not gonna run 4x4 down the road til i get a new driveshaft, just like to have it if i absolutely need it, or wanna play around like this
haha
 


Quick Reply: front driveshaft



All times are GMT -5. The time now is 10:16 PM.