Will 37-14.50-16'' toyo mts fit under my truck? Im ok with some rub but I dont want it to be stupid. Ive got quite a bit of offset already and Im clearing 35s with no problem.

Monster Truck's Sig:

Dads: 99 2500 Ext Cab Longbed 4X4 3.55s CTD, 5'', 47re, BHAF Outerwear Heat Sheild, Turnbuckle Wastgate, Fuel Pressure, Sucnoast Tripple Disk TC with custom vb work.
Mine: 95 Ext Cab SLT, Loaded, 5spd, 3.54s, Leveled 5'' Lift 35'' Toyos, 4'' Straight, Super B 57/66/14, Stage 2 Sticks, 3GSK, #60 Valve Springs, Stage 2 clutch, Custom Intake, Pateless, Boost and EGT on the pillar.

i think bigblue12 has 39.5 inch iroks on his truck with 5 inches of lift. he did some trimming though

2500HeavyDuty's Sig:

to much of an offset will cause a tire to rub also, but i thank you will be fine tho

slowtowpig's Sig:

1997 4dr 4x4 sb Powerstroke, 6in of lift,down pipe,custom 5in straight dual w/ 8in tips,6pos wildman chip, straight air filter, beans IDM, trans built by mikes trick shift,D66 turbo, 17*HPOP, wildman injectors,FPR shimmed, gauges, 37's on 20s, tv/dvd, cerwin vega mids/highs, PPI flat piston subs, 05 badges, superduty cab lights, shaved tailgate, 12000k HIDs, cobra 29ltd chrome edition cb

I would just like the opportunity to say...I have no idea.

Cumminscowboy_101's Sig:

1996 Dodge Cummins 3500 daully, 4x4 5 speed manual. Daul whips with Cobra CB, toolbox, straight pipe exhaust, custom air-flow tail gate, 2" block lift. Lots more to come in the near future!!
~~MEMBER~~BLOWIN' SMOKE GANG

37's will fit with 5 inches of lift and fender cutouts or fiberglass fenders for baja trucks. unless you run a factory backspace wheel and you get them under it. truck in avatar has 3 inch lift and fenders factory backspace wheel and 37's but its an 03

nmlakerat's Sig:

Blowin' Smoke Gang
Board of Directors.

They'll be close. You'll definitely rub at full lock, but hopefully just on the fender liners, it depends on what backspacing. You may need to trim the front bumper a little, and the back part of your wheel well. One other thing I noticed in your sig, no mention of an upgraded track bar. With 37's, your gonna wanna give Don Thuren a call and have him fab you up a new one, otherwise your gonna toast the one that came with your lift in a hurry. Might wanna look into a set of 4.10's to replace the 3.54's you have, it'll give your ride a little more pep off the line.

MotorOilMcCall's Sig:

99 2500 RC 4x4 5-Spd - Quad XZT, Leveling Kit, 35" Nitto's up front/Pro-Comp's rear, Ranch Hand Bumper, PPE Lift Pump

98 3500 12V QC 5x5 5-Spd - 191 DV's, 370 EDM's, 4K GSK, 17* Timing, SBC 3850 Puller Dual Disk, Big Input Shaft - SOLD

I have 37x 12.50 with 6" and lots of clearance if needed stack a leveling kit on the lift spirngs

sidekick's Sig:

2006 Ram 2500 6" Fabtech lift, 35" Toyo Open Country M/T tires,
18" Xtreme Alloy 6001 wheels, S&B cold air intake and air horn,
Magna Flow 5" turbo back exhaust, Mads Electronics Smarty, Edge Juice w/Attitude,
Devils Own Water Meth, BD Super B Special Turbo, BD Boost Fooler, Trans and Converter by GOEREND , Home made traction bars

I personally do Not recomend stacking a leveling kit under lifted springs.